Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM C

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit  


DESCRIPTION

The output speed sensor are installed on the case side face. The rotational sensor adopts the magnetic type rotational sensor that applies to the hall element to detect the number of revolutions accurately.

The output speed sensor detects the number of revolutions of the output shaft (the number of the sensor rotor teeth is 15).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory Note
P0722 Output Speed Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The vehicle is being driven.

2.

While driving, the output speed suddenly becomes 0. Or, the ratio with the turbine speed is abnormal (sensor system is open or short).

3.

5 seconds

4.

2-trip detection logic


DTC Detection Condition 2:
1.

At starting

2.

The C2 clutch cannot be engaged, which causes the vehicle not to start (only the turbine speed increases). (Trouble in automatic transmission assembly)

3.

5.5 seconds

4.

2-trip detection logic


·

Open or short in transmission revolution sensor (output speed sensor) circuit

·

Transmission revolution sensor (output speed sensor)

·

ECM

·

Automatic transmission assembly


Come on Blinks DTC stored -

·

MIL:"Comes on" means the MIL (Malfunction Indicator Light) illuminates.

·

Memory:"DTC stored" means the ECM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C332778E04
0.573,2.958 2.875,3.375 2.302,0.417 10 false Transmission Revolution Sensor (Output Speed Sensor) 1.771,1.063 2.229,1.26 0.458,0.198 10 false VCC 0.573,2.771 1.031,2.969 0.458,0.198 10 false C43 5.448,2.792 5.906,2.99 0.458,0.198 10 false C50 5.896,2.802 6.354,3 0.458,0.198 10 false ECM 1.708,1.615 2.167,1.813 0.458,0.198 10 false VOUT 1.781,2.146 2.24,2.344 0.458,0.198 10 false GND 5.323,1.052 5.781,1.25 0.458,0.198 10 false VBOP 5.323,1.635 5.781,1.833 0.458,0.198 10 false ROTP 5.313,2.188 5.771,2.385 0.458,0.198 10 false EOPT 2.198,0.938 2.396,1.115 0.198,0.177 10 false 1 2.198,1.469 2.396,1.646 0.198,0.177 10 false 2 2.188,1.99 2.385,2.167 0.198,0.177 10 false 3 5.063,0.938 5.521,1.135 0.458,0.198 10 false 48 5,1.49 5.458,1.688 0.458,0.198 10 false 70 5.021,2.031 5.479,2.229 0.458,0.198 10 false 92

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (OUTPUT SPEED SENSOR - ECM)
a.

Disconnect the C43 transmission revolution sensor (output speed sensor) connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C43-1 (VCC) - C50-48 (VBOP) Always Below 1 Ω
C43-2 (VOUT) - C50-70 (ROPT) Always Below 1 Ω
C43-3 (GND) - C50-92 (EOPT) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C43-1 (VCC) or C50-48 (VBOP) - Body ground Always 10 kΩ or higher
C43-2 (VOUT) or C50-70 (ROPT) - Body ground Always 10 kΩ or higher
C43-3 (GND) or C50-92 (EOPT) - Body ground Always 10 kΩ or higher



d.

Reconnect the C43 transmission revolution sensor (output speed sensor) connector.


e.

Reconnect the C50 ECM connector.

Result:
Proceed to
OK
NG




OK

2.REPLACE TRANSMISSION REVOLUTION SENSOR (OUTPUT SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TRANSMISSION REVOLUTION SENSOR (OUTPUT SPEED SENSOR)

NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / A/T / Trouble Codes.

Powertrain > A/T > Clear DTCs
50002 565


f.

Enter the following menus: Powertrain / A/T / Trouble Codes.

Powertrain > A/T > Trouble Codes
50001 565

g.

Check if diagnosis code P0722 is output.

HINT:

When not using the GTS or Techstream, refer to DTC CHECK / CLEAR.

Click hereDrivetrain>A4R AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR



Result:
Display (DTC Output) Proceed to
P0722 (for 1NR-VE) A
P0722 (for 2NR-VE) B
NO DTC C



A

B

C

END