Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM C

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0743  Shift Solenoid "E" Electrical  


DESCRIPTION

The ECM controls the shift solenoid valve DSL at a predetermined duty ratio, and performs a lock up operation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory Note
P0743 Shift Solenoid "E" Electrical 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

During energization of shift solenoid valve DSL.

2.

An open or short in the shift solenoid valve DSL circuit is detected.

3.

0.1 seconds

4.

1-trip detection logic


·

Open or short in shift solenoid valve DSL circuit

·

Transmission wire (shift solenoid valve DSL)

·

Shift solenoid valve DSL (transmission valve body assembly)

·

ECM


Come on Blinks DTC stored -

·

MIL:"Comes on" means the MIL (Malfunction Indicator Light) illuminates.

·

Memory:"DTC stored" means the ECM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C332780E02
0.781,2.104 2.51,2.375 1.729,0.271 10 false Shift Solenoid Valve DSL 3.219,1.135 4.448,1.365 1.229,0.229 10 false Transmission Wire 0.313,2.583 0.646,2.813 0.333,0.229 10 false C45 0.323,2.771 2.604,3.052 2.281,0.281 10 false Automatic Transmission Assembly 6.302,2.615 6.719,2.875 0.417,0.26 10 false ECM 5.813,1.844 6.229,2.104 0.417,0.26 10 false E02 5.583,1.688 5.75,1.948 0.167,0.26 10 false 5 5.51,0.896 5.771,1.156 0.26,0.26 10 false 46 5.802,1.01 6.219,1.271 0.417,0.26 10 false SLS 5.875,2.604 6.25,2.854 0.375,0.25 10 false C50 4.781,0.896 5.198,1.156 0.417,0.26 10 false 10 4.385,0.885 4.802,1.146 0.417,0.26 10 false H10

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DSL)
C314053C10
1.083,1.979 1.604,1.979 1.604,1.979 2.177,1.417 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 0.781,1.906 1.313,2.115 0.531,0.208 10 false H10
*a Front view of wire harness connector
(to Transmission wire)


a.

Disconnect the C45 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (H10) - Body ground 20°C (68°F) 12.2 to 13.4 Ω


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE DSL
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C50 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-46 (SLS) - C45-10 (H10) Always Below 1 Ω
C50-46 (SLS) or C45-10 (H10) - Body ground and other terminals Always 10k Ω or higher



c.

Reconnect the C50 ECM connector.


d.

Reconnect the C45 transmission wire connector.


Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE DSL
C313380C02
0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.833,0.354 2.146,0.51 0.313,0.156 10 false (-) 2.708,0.354 3.021,0.51 0.313,0.156 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve DSL)


a.

Remove the shift solenoid valve DSL.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid Connector (SL) - Solenoid Body (SL) 20°C (68°F) 12.2 to 13.4 Ω



c.

Connect the positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body.

OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG




OK

NG