Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM C

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  SLT Solenoid System Malfunction  


DESCRIPTION

The ECM controls the line pressure control solenoid assembly at an optimum duty ratio according to the driving condition to control the fluid pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory Note
P2716 SLT Solenoid System Malfunction 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

During energization of line pressure control solenoid assembly.

2.

An open or short in the line pressure control solenoid assembly circuit is detected.

3.

1 seconds

4.

1-trip detection logic


·

Open or short in line pressure control solenoid assembly circuit

·

Transmission wire (line pressure control solenoid assembly)

·

Line pressure control solenoid assembly (transmission valve body assembly)

·

ECM


Blinks Blinks DTC stored -

·

MIL:"Comes on" means the MIL (Malfunction Indicator Light) illuminates.

·

Memory:"DTC stored" means the ECM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C313580E05
0.583,2.031 1.042,2.229 0.458,0.198 10 false C50 0.583,2.208 1.042,2.406 0.458,0.198 10 false ECM 1.208,0.844 1.667,1.083 0.458,0.24 10 false SLT+ 1.208,1.094 1.823,1.292 0.615,0.198 10 false SLT- 1.667,0.76 2,1 0.333,0.24 10 false 66 1.656,1.01 2,1.25 0.344,0.24 10 false 44 2.521,0.76 2.833,0.958 0.313,0.198 10 false 9 2.521,1.01 2.833,1.208 0.313,0.198 10 false 3 2.75,0.76 3.208,0.958 0.458,0.198 10 false H11 2.75,1.01 3.208,1.208 0.458,0.198 10 false H4 5.083,0.896 7.083,1.26 2,0.365 10 false Line Pressure Control Solenoid Assembly 2.677,2.167 3.135,2.365 0.458,0.198 10 false C45 3.156,2.167 5.594,2.438 2.438,0.271 10 false Automatic Transmission Assembly 2.75,1.448 4.042,1.698 1.292,0.25 10 false Transmission Wire

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SLT) - LINE PRESSURE CONTROL SOLENOID ASSEMBLY)
C314053C14
1.156,1.979 1.521,1.979 1.521,1.979 2.313,1.406 true 0.885,0.438 1.531,0.438 1.531,0.438 2.344,1.073 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 0.865,1.896 1.177,2.104 0.313,0.208 10 false H11 0.667,0.375 1.198,0.604 0.531,0.229 10 false H4
*a Component without harness connected
(Transmission Wire)


a.

Disconnect the C45 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (H11) - 3 (H4) 20°C (68°F) 5.0 to 5.6 Ω



c.

Reconnect the C45 transmission wire connector.

Result:
proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT LINE PRESSURE CONTROL SOLENOID ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C45 transmission wire connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C45-9 (H11) - C50-66 (SLT+) Always Below 1 Ω
C45-3 (H4) - C50-44 (SLT-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C45-9 (H11) or C50-66 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
C45-3 (H4) or C50-44 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the C50 ECM connector.


e.

Reconnect the C45 transmission wire connector.


Result:
Display (DTC Output) Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT LINE PRESSURE CONTROL SOLENOID ASSEMBLY
C313379C03
0.708,0.531 0.885,0.531 0.885,0.531 1.5,0.896 true 0.708,2.667 0.885,2.667 0.885,2.667 1.5,3.031 true 2.625,0.521 2.458,0.521 2.458,0.521 1.833,0.896 true 2.615,2.667 2.448,2.667 2.448,2.667 1.823,3.042 true 0.094,0.135 0.406,0.292 0.313,0.156 10 false *a 0.583,2.594 0.938,2.865 0.354,0.271 10 false 2 0.583,0.479 0.938,0.75 0.354,0.271 10 false 2 2.75,0.448 3.104,0.719 0.354,0.271 10 false 1 2.698,2.604 3.052,2.875 0.354,0.271 10 false 1 1.177,4.24 1.531,4.51 0.354,0.271 10 false (+) 2.094,4.24 2.448,4.51 0.354,0.271 10 false (-)
*a Component without harness connected
(Line Pressure Control Solenoid Assembly)


a.

Remove the line pressure control solenoid assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect the positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body.

OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG




OK

NG

REPLACE LINE PRESSURE CONTROL SOLENOID ASSEMBLY (TRANSMISSION VALVE BODY ASSEMBLY)