Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015105 MANUAL TRANSMISSION ASSEMBLY A

M5S MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12371 1.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Install the rear No. 1 engine mounting insulator with new 2 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


b.

Temporarily install the rear No. 1 engine mounting insulator with rear engine mounting bracket to the rear engine support member sub-assembly with a new bolt.

NOTICE:

Securely tighten the bolt after installing the engine assembly with manual transmission assembly onto the vehicle.

for 1NR-VE: Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION

for 2NR-VE: Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION



Hide 12321D 2.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Temporarily connect the rear engine mounting bracket to the manual transmission assembly with the 3 bolts.


b.
C331636N01
2.031,1.031 2.198,1.208 0.167,0.177 10 true A 0.99,0.844 1.135,1 0.146,0.156 10 true B 1.51,0.771 1.656,0.927 0.146,0.156 10 true C

Temporarily tighten the bolt A.


c.

Securely tighten the 3 bolts in the following order; B, A and C.

Torque:
58.8 N*m (600 kgf*cm, 43 ft.*lbf)


Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket with the 2 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 33030 4.INSTALL MANUAL TRANSMISSION ASSEMBLY

a.
C331634N01
2.469,0.073 2.625,0.271 0.156,0.198 10 false A 0.875,0.052 1.031,0.25 0.156,0.198 10 false A 0.51,0.458 0.667,0.656 0.156,0.198 10 false A 0.375,0.938 0.531,1.135 0.156,0.198 10 false B 0.427,1.49 0.583,1.688 0.156,0.198 10 false C 0.688,1.854 0.844,2.052 0.156,0.198 10 false C 1.042,1.979 1.198,2.177 0.156,0.198 10 false C 2.188,1.958 2.344,2.156 0.156,0.198 10 false C 2.708,1.5 2.865,1.698 0.156,0.198 10 false C

Temporarily install the manual transmission assembly with the 9 bolts.

Bolt length:

57 mm (2.24 in.) for bolt A and bolt B

40 mm (1.57 in.) for bolt C


NOTICE:

Confirm that there are 2 knock pins on the transmission fitting surface of the engine assembly.



b.

Tighten the 3 bolts A to the specified torque.

Torque:
58.8 N*m (600 kgf*cm, 43 ft.*lbf)


c.

Tighten the bolt B and other 5 bolts C to the specified torque.

Torque:
Bolt B : 58.8 N*m (600 kgf*cm, 43 ft.*lbf)
Bolt C : 36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 28100 5.INSTALL STARTER ASSEMBLY (for 1NR-VE)

Hide 28100 6.INSTALL STARTER ASSEMBLY (for 2NR-VE)

Hide 7.INSTALL ENGINE WIRE

a.

Connect the clamps and connectors to the manual transmission assembly.


Hide 9.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for 1NR-VE)

Hide 10.INSTALL ENGINE AND TRANSMISSION ASSEMBLY (for 2NR-VE)