Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015281 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Stop Light Switch Circuit  


DESCRIPTION

When the stop light switch assembly is pressed, the operation signal is transmitted to the main body ECU (fuse block assembly). When the main body ECU (fuse block assembly) receives the signal, it turns on the stop light.

WIRING DIAGRAM

E328372E01
0.906,2.146 2.063,2.792 1.156,0.646 10 false Stop Light Switch Assembly 0.906,1.969 1.24,2.167 0.333,0.198 10 false E69 1.833,1.615 2.083,1.781 0.25,0.167 10 false - 1.833,1.052 2.167,1.25 0.333,0.198 10 false + 3.229,1.625 3.563,1.823 0.333,0.198 10 false 3E 3.24,1.417 3.573,1.615 0.333,0.198 10 false 10 3.24,1.063 3.573,1.26 0.333,0.198 10 false 3E 3.281,0.24 4.865,0.958 1.583,0.719 10 false 1 3.25,0.427 3.583,0.625 0.333,0.198 10 false 3A 2.083,0.917 4.083,1.833 2,0.917 10 false 1 2.083,1.5 4.083,2.417 2,0.917 10 false 2 4.542,0.604 6.542,1.521 2,0.917 10 false STOP 5.875,0.438 7.042,1.323 1.167,0.885 10 false STPB 5.875,1.615 7.042,2.5 1.167,0.885 10 false STPL 5.875,1.052 7.042,1.938 1.167,0.885 10 false STPH 1.563,0.417 2.729,1.302 1.167,0.885 10 false from Battery 3.938,2.229 6.531,2.656 2.594,0.427 10 false Main Body ECU (Fuse Block Assembly) 3.24,0.865 4.823,1.583 1.583,0.719 10 false 18

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (STOP SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop SW Stop light switch signal ON or OFF ON: Stop light switch on
OFF: Stop light switch off
-

OK:

Normal conditions listed above are displayed.


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY)
a.

Disconnect the 3A main body ECU (fuse block assembly) connector.


b.
E323364C01
1.5,0.417 2.083,0.667 0.583,0.25 0.156,0.219 0.469,0.375 0.313,0.156 10 false *a 1.688,0.469 2,0.667 0.313,0.198 10 false 3A
*a Component without harness connected
(to Main Body ECU (Fuse Block Assembly) connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the 3E main body ECU (fuse block assembly) connector.


b.

Disconnect the E69 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3E-18 - E69-1(+) Always Below 1 Ω
3E-10 - E69-2(-) Always Below 1 Ω
3E-18 or E69-1(+) - Body ground Always 10 kΩ or higher
3E-10 or E69-2(-) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR