Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0116  Engine Coolant Temperature Sensor System Range/Performance  


DESCRIPTION

Refer to DTC P0115.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P0115

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Sensor System Range/Performance Either of the following conditions is met (2 trip detection logic):
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and then next cold engine start is performed, the engine coolant temperature sensor value does not change.


·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A198823E43
0.854,1.135 1.417,1.396 0.563,0.26 10 40 km/h 1.021,1.771 1.417,2 0.396,0.229 10 Idling 2.771,2.531 3.917,2.75 1.146,0.219 10 5 minutes or more 4.167,0.208 5.833,0.417 1.667,0.208 10 Total of 5 minutes or more 2.115,1.917 2.417,2.167 0.302,0.25 10 [A] 3.25,1.646 3.5,1.917 0.25,0.271 10 [B] 3.99,2.875 4.229,3.115 0.24,0.24 10 [C] 6.146,2.865 6.417,3.083 0.271,0.219 10 [E] 0.229,2.042 1.417,2.25 1.188,0.208 10 Ignition Switch ON 4.865,0.656 5.167,0.917 0.302,0.26 10 [D] 1.385,3.146 5.99,3.396 4.604,0.25 10 HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Enter the following menus: Powertrain / EFI / Data List / All Data / Engine coolant temperature.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


12.

Read the pending DTCs [E].

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are output simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / All Data / Engine coolant temperature. If the Engine coolant temperature value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs and other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

Inspect the thermostat (opening temperature).

Click hereEngine / Hybrid System>2NR-VE COOLING>THERMOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

NG