The front pretensioner squib LH circuit consists of the center airbag sensor assembly and front seat outer belt assembly LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1905/74 | Passenger Seat Side Pretensioner Short | One of the following conditions is met:
·
The center airbag sensor assembly detects a line short circuit signal in the front pretensioner squib LH circuit during the primary check. ·
A front pretensioner squib LH malfunction. ·
A center airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1906/74 | Passenger Seat Side Pretensioner Open | One of the following conditions is met:
·
The center airbag sensor assembly detects an open circuit signal in the front pretensioner squib LH circuit. ·
A front pretensioner squib LH malfunction. ·
A center airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1907/74 | Passenger Seat Side Pretensioner GND Short | One of the following conditions is met:
·
The center airbag sensor assembly detects a short circuit to ground signal in the front pretensioner squib LH circuit. ·
A front pretensioner squib LH malfunction. ·
A center airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Center airbag sensor assembly |
DTC is output in check mode |
| B1908/74 | Passenger Seat Side Pretensioner BATT Short | One of the following conditions is met:
·
The center airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner squib LH circuit. ·
A front pretensioner squib LH malfunction. ·
A center airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Center airbag sensor assembly |
DTC is output in check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter check mode (signal check) with the intelligent tester or Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Center Airbag Sensor Assembly |
| *3 | Connector C |
| *4 | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt assembly LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1905/74, B1906/74, B1907/74 or B1908/74 are not output.
Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connectors from the center airbag sensor assembly.
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Floor Wire |
| *3 | Center Airbag Sensor Assembly |
Check that the connectors (on the center airbag sensor assembly side and front seat outer belt assembly LH side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Floor Wire |
| *3 | Center Airbag Sensor Assembly |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J14-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
| J14-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-1 (P-) - J14-2 (P+) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-1 (P-) - J14-2 (P+) | Always | 1 MΩ or higher |
| J14-1 (P-) - Body ground | Always | 1 MΩ or higher |
| J14-2 (P+) - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Center Airbag Sensor Assembly |
Connect the connectors to the front seat outer belt assembly LH and center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1905/74, B1906/74, B1907/74 or B1908/74 are not output.
Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG