Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1233/35  Yaw Rate Sensor Open / Short  C1245/31  Abnormal signal G sensor  C1279/91  G Sensor (Check Mode)  C1322/97  STS System Grounded  C1393/93  Yaw Rate Sensor (Check Mode)  


DESCRIPTION

The yaw rate sensor and the G sensor are built-into the skid control ECU (brake actuator assembly).

DTCs C1279/91, C1322/71 and C1393/93 are cleared when the yaw rate sensor and G sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1279/91, C1322/71 and C1393/93 are output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1233/35 Yaw Rate Sensor Open / Short With ignition switch ON or during driving at higher speeds than a set speed, abnormalities in the yaw rate sensor inside the brake actuator and sensor signal values are detected.
·

Improper installation of yaw rate sensor (brake actuator assembly)

·

The yaw rate sensor built-into the skid control ECU (brake actuator assembly) has malfunction

·

Improper installation of suspension and related parts

·

Improper installation of steering and related parts

·

Switch base (steering sensor)


-
C1245/31 Abnormal signal G sensor With ignition switch ON or during driving at higher speeds than a set speed, abnormalities in the front/rear G sensor and sensor signal values are detected.
·

Improper installation of G sensor (brake actuator assembly)

·

The G sensor built-into the skid control ECU (brake actuator assembly) has malfunction

·

Improper installation of suspension and related parts

·

Improper installation of steering and related parts

·

Switch base (steering sensor)


-
C1279/91 G Sensor (Check Mode) Stored during Test Mode.
·

Improper installation of G sensor (brake actuator assembly)

·

The G sensor built-into the skid control ECU (brake actuator assembly) has malfunction

·

Improper installation of suspension and related parts

·

Improper installation of steering and related parts

·

Switch base (steering sensor)


-
C1322/97 STS System Grounded Stored during Test Mode.
·

Improper installation of G sensor (brake actuator assembly)

·

The G sensor built-into the skid control ECU (brake actuator assembly) has malfunction

·

Improper installation of suspension and related parts

·

Improper installation of steering and related parts

·

Switch base (steering sensor)


-
C1393/93 Yaw Rate Sensor (Check Mode) Stored during Test Mode.
·

Improper installation of yaw rate sensor (brake actuator assembly)

·

The yaw rate sensor built-into the skid control ECU (brake actuator assembly) has malfunction

·

Improper installation of suspension and related parts

·

Improper installation of steering and related parts

·

Switch base (steering sensor)


-

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the troubleshooting, be sure to check the installation conditions of the suspension, steering, and the related parts.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK BRAKE ACTUATOR ASSEMBLY INSTALLATION
a.

Check that the skid control ECU (brake actuator assembly) is installed properly with no rattling or deformation in its installation area, or deformation of mounting bracket.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>INSTALLATION

OK:

Installed properly.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (YAW RATE SENSOR AND G SENSOR)

NG

INSTALL BRAKE ACTUATOR ASSEMBLY CORRECTLY

2.READ VALUE USING GTS (YAW RATE SENSOR AND G SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw rate sensor 1 Yaw rate sensor Min.: -128 deg/s
Max.: 127 deg/s
Vehicle stopped: 1 deg/s
Turning right: -128 to 3 deg/s
Turning left: 2 to 127 deg/s
-
Right/Left G (Controlled) Right/Left G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During turning: Changes in proportion with acceleration
Front/Rear G (Controlled) Front/Rear G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During acceleration/deceleration: Changes in proportion with acceleration


g.

Drive at low speeds and check the changes in output values of yaw rate sensor and the G sensor when making turns and applying hard braking.

OK:

The output values change in proportion to the vehicle inclination of front/rear and left/right.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STEERING ANGLE SENSOR)

NG

3.READ VALUE USING GTS (STEERING ANGLE SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering angle sensor Steering angle sensor Min.: -3276.8 deg
Max.: 3276.8 deg
Turning left: Positive value increases
Turning right: Negative value decreases
-

OK:

The output values change in response to the steering operation.



Result:
Proceed to
OK
NG



OK

NG