Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241/15  Voltage Dropped / Over  C1241/16  Voltage Dropped / Over  C1300/77  ECU Inside  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs DTCs when abnormality occurs in its power source circuit and enters fail-safe mode to prevent activation of ABS control.

This DTC is output when +IG terminal voltage becomes higher or lower than the specified value due to abnormalities occurred in the power source or charging system including battery and alternators.

Fail-safe mode ends when the power source voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1241/15 Voltage Dropped / Over
·

With ignition switch ON or during driving at higher speeds than a set speed, decreased power source voltage of skid control ECU (brake actuator assembly) is detected.

·

With ignition switch ON, the motor power source voltage becomes lower than the power source voltage.


·

Power source circuit

·

Open or short in wire harness

·

Deformation, damage, or poor connections of connector terminals

·

Voltage decrease due to changes in electrical load

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


-
C1241/16 Voltage Dropped / Over With ignition switch ON, power source overvoltage of skid control ECU (brake actuator assembly) is detected.
·

Power source circuit

·

Open or short in wire harness

·

Deformation, damage, or poor connections of connector terminals

·

Voltage increase due to changes in electrical load

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


-
C1300/77 ECU Inside Skid control ECU (Brake actuator assembly) internal error Skid control ECU (brake actuator assembly) -

WIRING DIAGRAM

C314505E03
1.115,1.135 2.458,1.844 1.344,0.708 10 false from IG1 Relay 3.792,1.313 4.708,1.719 0.917,0.406 10 false ECU-IG1 5.958,1.156 6.396,1.479 0.438,0.323 10 false +IG 6,2.854 6.438,3.177 0.438,0.323 10 false GND1 5.708,1.031 6.146,1.354 0.438,0.323 10 false 12 5.719,2.75 6.156,3.073 0.438,0.323 10 false 25 5.583,3.948 7.115,4.469 1.531,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 5.552,3.792 5.99,4.115 0.438,0.323 10 false A13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+IG TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK TERMINAL VOLTAGE (+IG TERMINAL)
a.
C330019C55
1.5,0.167 1.917,0.417 0.417,0.25 2.406,0.448 2.25,0.99 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.583,0.208 2.135,0.469 0.552,0.26 10 false A13 2.448,0.302 2.906,0.5 0.458,0.198 10 false +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.READ VALUE USING GTS (+IG 1 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (+IG 1 VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+IG 1 voltage +IG voltage value Min.: 0.00 V
Max.: 20.00 V
Ignition switch on: 11 to 14 V Changes in proportion to battery voltage

OK:

Normal



e.

Using the GTS, check the input of the stop light switch operation when the brake pedal is operated.

Result:
Proceed to
OK
NG




OK

5.RECONFIRM DTC

NG

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR




A

B