Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1251/51  Motor Pump System  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs DTCs when abnormality occurs in the motor drive circuit and enters fail-safe mode to prevent activation of ABS control.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1251/51 Motor Pump System When turning the ignition switch to ON or at first starting of the vehicle, open, short, or malfunction occurs in the pump motor and its drive circuit.
·

ABS fuse

·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)

·

Skid control ECU (Brake actuator assembly)


-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C330019C56
1.51,0.25 1.927,0.5 0.417,0.25 2.719,0.406 2.51,0.406 2.51,0.406 2.427,0.99 true 0.573,0.406 0.75,0.406 0.75,0.406 0.865,0.99 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.604,0.292 2,0.583 0.396,0.292 10 false A13 0.167,0.333 0.677,0.635 0.51,0.302 10 false GND2 2.781,0.323 3.292,0.625 0.51,0.302 10 false +BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (GND2) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
A13-13 (+BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly). Therefore, the ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B