Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.
DTC C2191/91 is stored only during the signal check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C2174/74 | Vehicle Speed Signal Malfunction | All conditions below are met:
·
DTC C2121/21, C2122/22, C2123/23, C2124/24 and/or C2125/25 ·
Vehicle speed signal malfunction |
·
Combination meter ·
Vehicle speed signal circuit ·
Harness or connector ·
Tire pressure warning ECU and receiver ·
Tire pressure warning valve and transmitter |
| C2191/91 | Vehicle Speed Signal Error (Test Mode DTC) | Test mode procedure is performed. | ·
Meter / gauge system (speed signal) ·
Vehicle speed signal circuit ·
Harness or connector ·
Tire pressure warning ECU and receiver |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
When the speedometer needle is not moving, first troubleshoot the meter/gauge system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check that the values indicated on the GTS and on the combination meter assembly are the same.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed reading | min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph) |
Actual vehicle speed | Speed indicated on combination meter assembly |
Vehicle speed indicated on the GTS indicates the actual speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch ON.
Perform a driving test.
Check for DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
The time required for DTC C2174 to be stored is 20 minutes.
| Result | Proceed to |
|---|---|
| DTC C2174 is not output | A |
| DTC C2174 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the tire pressure warning ECU and receiver K6 connector.
Disconnect the combination meter assembly E34 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K6-2 (SPEED) - E34-10 (SPDO) | Always | Below 1 Ω |
| K6-2 (SPEED) or E34-10 (SPDO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the tire pressure warning ECU and receiver.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.
Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).
| Result | Proceed to |
|---|---|
| DTC C2191 is not cleared | A |
| DTC C2191 is cleared | B |
A
B