Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.09
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM D

NETWORKING  CAN COMMUNICATION SYSTEM  DIAGNOSIS SYSTEM  


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

ECM


ii.

Combination meter assembly


iii.

Skid control ECU (brake actuator assembly)


iv.

Main body ECU (fuse block assembly)


v.

Airbag ECU assembly


vi.

Power steering ECU assembly


vii.

DLC3


viii.

Combination switch ECU (switch base)




CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION


a.

The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

ECU/Sensor Name GTS or Techstream Display Applicability
ECM ECM (Engine) Installed on all vehicles
TCM for Automatic Transmission
Combination meter assembly Combination Meter Installed on all vehicles
Skid control ECU (brake actuator assembly) Skid Control (ABS/VSC/TRAC) Installed on all vehicles
Main body ECU (fuse block assembly) Main Body Installed on all vehicles
Airbag ECU assembly Airbag Installed on all vehicles
Power steering ECU assembly Power Steering (EPS) Installed on all vehicles
Combination switch ECU (switch base) Combination Switch Installed on all vehicles

HINT:

The names of ECUs and sensors shown on the GTS or Techstream display may differ from those shown in the DTC Table by ECU section.




CAN BUS CHECK


CAN Bus Check
50007
HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS or Techstream.


a.

Using the GTS or Techstream, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus (gateway function equipped ECU that does not have history of connected ECUs)*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus (gateway function equipped ECU that has history of connected ECUs)*3 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS or Techstream, check the DLC3 branch and the V bus main bus lines for a malfunction.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Example: Open in both CAN branch lines of ECU B on the V bus

C240692C10
5.854,0.063 6.115,0.323 0.26,0.26 10 false *a 0.396,3.198 1.063,3.583 0.667,0.385 10 false DLC3 5.865,0.51 6.125,0.771 0.26,0.26 10 false *b 5.469,1 5.729,1.26 0.26,0.26 10 false *c 5.469,1.521 5.729,1.781 0.26,0.26 10 false *d 5.563,2.042 5.823,2.302 0.26,0.26 10 false *e 4.281,3.052 4.542,3.313 0.26,0.26 10 false *f
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color changes to red or yellow *f CAN Bus Check Screen


HINT:

When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.



c.
C240693C05
0.271,1.708 0.51,1.906 0.24,0.198 10 false *a 2.875,2.448 3.115,2.646 0.24,0.198 10 false *b 1.01,2.458 1.25,2.656 0.24,0.198 10 false *c
*a Background color periodically changes to yellow or red
*b Not displayed or background color is yellow or red
*c Not displayed


If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.

Example: Open in a CAN branch line for ECU D on the V bus

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus (gateway function equipped ECU that does not have history of connected ECUs)*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub Bus (gateway function equipped ECU that has history of connected ECUs)*3 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.

·

The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.




d.
C240694C05
0.24,1.708 0.458,1.938 0.219,0.229 10 false *a 2.875,2.417 3.094,2.646 0.219,0.229 10 false *a
*a Not displayed or background color changes to red


If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.

Example: Open in both CAN branch lines of ECU C on the V bus

HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS or Techstream to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.




e.
C240695C05
3,1.5 3.188,1.677 0.188,0.177 10 false *a
*a Background color changes to red


If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of ECU G on the sub bus

HINT:
·

A communication error in a sub bus does not affect the V bus or other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU A and B are not displayed or their background color changes to red.)

C240696C06
0.385,3.198 0.906,3.469 0.521,0.271 10 false DLC3 5.844,0.042 6.125,0.271 0.281,0.229 10 false *a 5.844,0.521 6.125,0.75 0.281,0.229 10 false *b 5.469,1.01 5.75,1.24 0.281,0.229 10 false *c 5.469,1.531 5.75,1.76 0.281,0.229 10 false *d 5.563,2.042 5.844,2.271 0.281,0.229 10 false *e 4.271,3.031 4.552,3.26 0.281,0.229 10 false *f
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color is red *f CAN Bus Check Screen


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU I and J are not displayed or their background color changes to red.)

C240697C05
0.385,3.198 0.823,3.417 0.438,0.219 10 false DLC3 5.854,0.042 6.146,0.333 0.292,0.292 10 false *a 5.583,2.052 5.865,2.281 0.281,0.229 10 false *e 5.854,0.521 6.135,0.75 0.281,0.229 10 false *b 5.49,1 5.771,1.229 0.281,0.229 10 false *c 5.49,1.521 5.771,1.75 0.281,0.229 10 false *d 4.271,3.031 4.552,3.26 0.281,0.229 10 false *f 2.719,1.417 3,1.646 0.281,0.229 10 false *g
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of Malfunction
*e Not displayed or background color is red *f CAN Bus Check Screen
*g Gateway Function Equipped ECU - -



h.
C240698C06
0.052,0.031 0.323,0.26 0.271,0.229 10 false *a 0.115,2.375 0.385,2.604 0.271,0.229 10 false *b 2.865,1.823 3.135,2.052 0.271,0.229 10 false *c 0.302,1.823 0.573,2.052 0.271,0.229 10 false *c 2.854,4.021 3.125,4.25 0.271,0.229 10 false *c
*a When any of the following malfunctions occur on the V bus
*b When any of the following malfunctions occur on a sub bus
*c Not displayed


When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

HINT:
·

When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the V bus or other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.





HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


a.

If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

HINT:

Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.


i.

If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

C253779C05
6.904,0.248 7.148,0.437 0.244,0.189 10 : *a 4.43,0.174 5.346,0.397 0.916,0.223 10 Tester display 2.194,0.173 3.048,0.376 0.854,0.204 10 Output DTC 0.723,0.177 1.53,0.381 0.808,0.204 10 Output from
*a Items to be Checked - -


NOTICE:
·

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

·

Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS or Techstream may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)



HINT:

As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



ii.

If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

C253780C04
6.896,0.271 7.156,0.458 0.26,0.188 10 : *a 4.417,0.167 5.333,0.385 0.917,0.219 10 Tester display 2.188,0.167 3.042,0.375 0.854,0.208 10 Output DTC 0.719,0.177 1.531,0.385 0.813,0.208 10 Output from
*a Items to be Checked - -


NOTICE:

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.


HINT:

If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.



iii.

When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.



b.

To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

C240704C06
3.615,0.333 3.823,0.333 false 1.313,1.813 1.052,2.354 1.052,2.354 0.875,2.354 false 4.833,0.333 5.115,0.531 0.281,0.198 10 false : *d 3.854,0.26 4.042,0.458 0.188,0.198 10 false *f 3.656,0.844 3.844,1.042 0.188,0.198 10 false *c 0.427,1.677 0.615,1.875 0.188,0.198 10 false *b 0.698,2.26 0.885,2.458 0.188,0.198 10 false *e 0.896,2.708 1.698,2.906 0.802,0.198 10 false Output from 2.49,2.708 3.292,2.906 0.802,0.198 10 false Output DTC 4.625,2.698 5.573,2.896 0.948,0.198 10 false Tester display 1.135,4.49 1.438,4.688 0.302,0.198 10 false : *a
*a Items to be Checked *b ECM
*c Gateway Function Equipped ECU *d Location of Malfunction
*e V Bus *f Sub Bus


NOTICE:

This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.


HINT:
·

As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.

·

When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.




c.

When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

·

Short between CAN lines (CANH and CANL)

·

Short between a CAN line (CANH or CANL) and ground

·

Short between a CAN line (CANH or CANL) and +B

·

Open in a CAN branch line (CANH or CANL) of an ECU or sensor

·

Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor




DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS or Techstream.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

ECM

Powertrain > EFI > Trouble Codes
50001 591
HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0129 Communication with ABS/VSC (Receive) No communication from skid control ECU (brake actuator assembly) for 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. MIL illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0142 Communication with BODY ECU (Receive) No communication from main body ECU (fuse block assembly) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. MIL illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0151 Communication with A/B (Receive) No communication from airbag ECU assembly for 5 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10 V or more.


Turn the ignition switch to ON and wait at least 6 seconds. MIL illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0155 Communication with meter (Receive) No communication from combination meter assembly for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. MIL illuminates. DTC is stored until it is cleared using the GTS or Techstream.


b.

Combination Meter Assembly

Body Electrical > Meter > Trouble Codes
50001 572
HINT:
·

This ECU uses the CAN communication system for DTC communication.

·

LCD codes can be displayed on the multi-information display in the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

·

*1: for Automatic Transmission

·

*2: w/ VSC



DTC
(LCD Code)
Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073
(0022)
Communication with CAN When bus off is detected more than 10 times.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 60 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0100
(0051)
Communication with EFI No communication from ECM for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. MIL illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0101*1
(0052)*1
Communication with EAT/CVT No communication from TCM (ECM) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0129
(0053)
Communication with ABS/VSC No communication from skid control ECU (brake actuator assembly) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds.
·

BRAKE warning light illuminates.

·

ABS warning light illuminates.

·

SLIP indicator light illuminates.*2


DTC is stored until it is cleared using the GTS or Techstream.
U0131
(0066)
Communication with EPS No communication from power steering ECU assembly for 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. EPS warning light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0142
(0011)
Communication with ITC No communication from main body ECU (fuse block assembly) for 1.4 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 2.4 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0151
(0068)
Communication with A/B ECU No communication from airbag ECU assembly for 5 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 6 seconds. SRS warning light illuminates. DTC is stored until it is cleared using the GTS or Techstream.


c.

Skid Control ECU (Brake Actuator Assembly)(w/o VSC)

HINT:

The skid control ECU (brake actuator assembly) is connected to the CAN communication system, but the skid control ECU (brake actuator assembly) does not store or output CAN communication DTCs.



d.

Skid Control ECU (Brake Actuator Assembly)(w/ VSC)

Chassis > ABS/VSC/TRC > Trouble Codes
50001 573
HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
C1202 Master Reservoir Level No communication from main body ECU (fuse block assembly) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 2 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
C1207 Shift Signal (Reverse) No communication from ECM for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 2 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0073 Abnormal Communication with CAN When bus off is detected.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 60 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0100 Abnormal Communication with EFI No communication from ECM for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 2 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0126 Abnormal Communication with Steering Sensor No communication from combination switch ECU (switch base) for 1 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 2 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.
U0155 Abnormal Communication with Meter No communication from combination meter assembly for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the skid control ECU (brake actuator assembly) is 10 to 16 V.


Turn the ignition switch to ON and wait at least 2 seconds. SLIP indicator light illuminates. DTC is stored until it is cleared using the GTS or Techstream.


e.

Main Body ECU (Fuse Block Assembly)

Body Electrical > Body > Trouble Codes
50001 594
HINT:
·

This ECU uses the CAN communication system for DTC communication.

·

LCD codes can be displayed on the multi-information display in the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

·

*: for Automatic Transmission



DTC
(LCD Code)
Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073
(0282)
CAN communications fault (Bus OFF) When bus off is detected more than 10 times.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 60 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0100
(0283)
EFI ECU CAN communications fault No communication from ECM for 1 to 3 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 4 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0101*
(0284)*
CVT/AT ECU CAN communications fault No communication from TCM (ECM) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0121
(0285)
ABS/VSC ECU CAN communications fault No communication from skid control ECU (brake actuator assembly) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0155
(0287)
Meter CAN communications fault No communication from combination meter assembly for 1 to 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U1000
(0281)
CAN communications fault (Resistor) No communication from all ECUs for 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U1112
(0288)
Combi SW CAN communications fault No communication from combination switch ECU (switch base) for 1 second or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS or Techstream.


f.

Airbag ECU Assembly

HINT:

The airbag ECU assembly is connected to the CAN communication system, but the airbag ECU assembly does not store or output CAN communication DTCs.



g.

Power Steering ECU Assembly

Chassis > EPS > Trouble Codes
50001 581
HINT:

This ECU uses the CAN communication system for DTC communication.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 CAN communication error (EFI) No communication from ECM for 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the power steering ECU assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS or Techstream.
U0155 CAN communication error (meter) No communication from combination meter assembly for 2 seconds or more.
(1 trip detection logic)
Both conditions are met:
·

The ignition switch is turned to ON and 1 second or more.

·

The power source voltage of the power steering ECU assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS or Techstream.


h.

Combination Switch ECU (Switch Base)

HINT:

The combination switch ECU (switch base) is connected to the CAN communication system, but the combination switch ECU (switch base) does not store or output CAN communication DTCs.




DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU and sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS or Techstream because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or short to ground in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS or Techstream screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



- Trouble Mode (Open in One CAN Branch Line)
V Bus
Output ECU Output DTC
(LCD Code)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Main Body ECU Communication Stop Mode
Click here(Click here)
Center Airbag Sensor Communication Stop Mode
Click here(Click here)
V Bus ECM U0129 X ▲ ▲
U0142 ▲ X ▲
U0151 ▲ ▲ X
U0155 ▲ ▲ ▲
Combination Meter Assembly U0073
(0022)
▲ ▲ ▲
U0100
(0051)
▲ ▲ ▲
U0101
(0052)
▲ ▲ ▲
U0129
(0053)
X ▲ ▲
U0131
(0066)
▲ ▲ ▲
U0142
(0011)
▲ X ▲
U0151
(0068)
▲ ▲ X
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 X X ▲
C1207 X ▲ ▲
U0073 X ▲ ▲
U0100 X ▲ ▲
U0126 X ▲ ▲
U0155 X ▲ ▲
Main Body ECU (Fuse Block Assembly) U0073
(0282)
▲ X ▲
U0100
(0283)
▲ X ▲
U0101
(0284)
▲ X ▲
U0121
(0285)
X X ▲
U0155
(0287)
▲ X ▲
U1000
(0281)
▲ X ▲
U1112
(0288)
▲ X ▲
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 ▲ ▲ ▲
U0155 ▲ ▲ ▲
Combination Switch ECU (Switch Base) - - - -

HINT:
·

X: DTC is likely to be output.

·

▲: DTC is unlikely to be output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (Open in One CAN Branch Line)
V Bus
Output ECU Output DTC
(LCD Code)
Power Steering ECU Communication Stop Mode
Click here(Click here)
Combination Switch ECU Communication Stop Mode
Click here(Click here)
DLC3
V Bus ECM U0129 ▲ ▲ -
U0142 ▲ ▲ -
U0151 ▲ ▲ -
U0155 ▲ ▲ -
Combination Meter Assembly U0073
(0022)
▲ ▲ -
U0100
(0051)
▲ ▲ -
U0101
(0052)
▲ ▲ -
U0129
(0053)
▲ ▲ -
U0131
(0066)
X ▲ -
U0142
(0011)
▲ ▲ -
U0151
(0068)
▲ ▲ -
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 ▲ ▲ -
C1207 ▲ ▲ -
U0073 ▲ ▲ -
U0100 ▲ ▲ -
U0126 ▲ X -
U0155 ▲ ▲ -
Main Body ECU (Fuse Block Assembly) U0073
(0282)
▲ ▲ -
U0100
(0283)
▲ ▲ -
U0101
(0284)
▲ ▲ -
U0121
(0285)
▲ ▲ -
U0155
(0287)
▲ ▲ -
U1000
(0281)
▲ ▲ -
U1112
(0288)
▲ X -
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 X ▲ -
U0155 X ▲ -
Combination Switch ECU (Switch Base) - - - -

HINT:
·

X: DTC is likely to be output.

·

▲: DTC is unlikely to be output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC
(LCD Code)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Main Body ECU Communication Stop Mode
Click here(Click here)
Center Airbag Sensor Communication Stop Mode
Click here(Click here)
V Bus ECM U0129 ○ - -
U0142 - ○ -
U0151 - - ○
U0155 - - -
Combination Meter Assembly U0073
(0022)
- - -
U0100
(0051)
- - -
U0101
(0052)
- - -
U0129
(0053)
○ - -
U0131
(0066)
- - -
U0142
(0011)
- ○ -
U0151
(0068)
- - ○
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 ○ ○ -
C1207 ○ - -
U0073 ○ - -
U0100 ○ - -
U0126 ○ - -
U0155 ○ - -
Main Body ECU (Fuse Block Assembly) U0073
(0282)
- ○ -
U0100
(0283)
- ○ -
U0101
(0284)
- ○ -
U0121
(0285)
○ ○ -
U0155
(0287)
- ○ -
U1000
(0281)
- ○ -
U1112
(0288)
- ○ -
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 - - -
U0155 - - -
Combination Switch ECU (Switch Base) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (Open in Both CAN Branch Lines)
V Bus
Output ECU Output DTC
(LCD Code)
Power Steering ECU Communication Stop Mode
Click here(Click here)
Combination Switch ECU Communication Stop Mode
Click here(Click here)
DLC3
V Bus ECM U0129 - - -
U0142 - - -
U0151 - - -
U0155 - - -
Combination Meter Assembly U0073
(0022)
- - -
U0100
(0051)
- - -
U0101
(0052)
- - -
U0129
(0053)
- - -
U0131
(0066)
○ - -
U0142
(0011)
- - -
U0151
(0068)
- - -
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 - - -
C1207 - - -
U0073 - - -
U0100 - - -
U0126 - ○ -
U0155 - - -
Main Body ECU (Fuse Block Assembly) U0073
(0282)
- - -
U0100
(0283)
- - -
U0101
(0284)
- - -
U0121
(0285)
- - -
U0155
(0287)
- - -
U1000
(0281)
- - -
U1112
(0288)
- ○ -
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 ○ - -
U0155 ○ - -
Combination Switch ECU (Switch Base) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (Open in One CAN Main Bus Line)
V Bus
Output ECU Output DTC
(LCD Code)
ECM Communication Stop Mode
Click here(Click here)
Main Body ECU (Fuse Block Assembly) to No. 1 CAN Junction Connector Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus ECM U0129 X ▲ ▲
U0142 X ▲ ▲
U0151 X X ▲
U0155 X X X
Combination Meter Assembly U0073
(0022)
▲ ▲ X
U0100
(0051)
X X X
U0101
(0052)
X X X
U0129
(0053)
X X X
U0131
(0066)
▲ ▲ X
U0142
(0011)
▲ ▲ X
U0151
(0068)
▲ ▲ X
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 X ▲ ▲
C1207 X ▲ ▲
U0073 ▲ ▲ ▲
U0100 X ▲ ▲
U0126 X X ▲
U0155 X X X
Main Body ECU (Fuse Block Assembly) U0073
(0282)
▲ ▲ ▲
U0100
(0283)
X ▲ ▲
U0101
(0284)
X ▲ ▲
U0121
(0285)
X ▲ ▲
U0155
(0287)
▲ X X
U1000
(0281)
▲ ▲ ▲
U1112
(0288)
▲ X ▲
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 X X ▲
U0155 ▲ ▲ X
Combination Switch ECU (Switch Base) - - - -

HINT:
·

X: DTC is likely to be output.

·

▲: DTC is unlikely to be output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (Open in Both CAN Main Bus Line)
V Bus
Output ECU Output DTC
(LCD Code)
ECM Communication Stop Mode
Click here(Click here)
Main Body ECU (Fuse Block Assembly) to No. 1 CAN Junction Connector Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus ECM U0129 ○ - -
U0142 ○ - -
U0151 ○ ○ -
U0155 ○ ○ ○
Combination Meter Assembly U0073
(0022)
- - ○
U0100
(0051)
○ ○ ○
U0101
(0052)
○ ○ ○
U0129
(0053)
X ○ ○
U0131
(0066)
- - ○
U0142
(0011)
- ○ ○
U0151
(0068)
- - ○
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 X - -
C1207 ○ - -
U0073 - - -
U0100 ○ - -
U0126 X ○ -
U0155 X ○ ○
Main Body ECU (Fuse Block Assembly) U0073
(0282)
- - -
U0100
(0283)
○ - -
U0101
(0284)
○ - -
U0121
(0285)
X - -
U0155
(0287)
- ○ ○
U1000
(0281)
- - -
U1112
(0288)
- ○ -
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 ○ ○ -
U0155 - - ○
Combination Switch ECU (Switch Base) - - - -

HINT:
·

○: DTC is output.

·

X: DTC is likely to be output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC



- Trouble Mode (CAN Bus Lines Short Circuit or Short to GND)
V Bus
Output ECU Output DTC
(LCD Code)
CANH to CANL CANH to Short to Ground CANL to Short to Ground
V Bus ECM U0129 ○ ○ ○
U0142 ○ ○ ○
U0151 ○ ○ ○
U0155 ○ ○ ○
Combination Meter Assembly U0073
(0022)
○ ○ ○
U0100
(0051)
○ ○ ○
U0101
(0052)
○ ○ ○
U0129
(0053)
○ ○ ○
U0131
(0066)
○ ○ ○
U0142
(0011)
○ ○ ○
U0151
(0068)
○ ○ ○
Skid Control ECU (Brake Actuator Assembly)*1 - - - -
Skid Control ECU (Brake Actuator Assembly)*2 C1202 ○ ○ ○
C1207 ○ ○ ○
U0073 ○ ○ ○
U0100 ○ ○ ○
U0126 ○ ○ ○
U0155 ○ ○ ○
Main Body ECU (Fuse Block Assembly) U0073
(0282)
○ ○ ○
U0100
(0283)
○ ○ ○
U0101
(0284)
○ ○ ○
U0121
(0285)
○ ○ ○
U0155
(0287)
○ ○ ○
U1000
(0281)
○ ○ ○
U1112
(0288)
○ ○ ○
Airbag ECU Assembly - - - -
Power Steering ECU Assembly U0100 ○ ○ ○
U0155 ○ ○ ○
Combination Switch ECU (Switch Base) - - - -

HINT:
·

○: DTC is output.

·

-: DTC is not output.

·

*1: w/o VSC

·

*2: w/ VSC





CAN BUS WAVEFORMS


C230845E12
4.708,0.281 4.594,0.281 4.594,0.281 4.427,0.885 false 4.469,0.854 4.417,0.896 4.417,0.896 4.417,0.844 false 6.677,3.698 5.76,2.594 true 5.771,2.688 5.75,2.583 5.75,2.583 5.823,2.594 false 3.844,3.771 3.979,3.771 3.979,3.771 5.073,2.594 true 5.073,2.698 5.083,2.583 5.083,2.583 4.99,2.604 false 2.24,0.688 2.49,0.281 2.49,0.281 2.646,0.281 false 4.271,4.365 5.156,4.365 false 5.156,4.365 5.469,3.688 false 5.281,3.063 5.844,3.365 0.563,0.302 10 false ECU 3.365,3.063 3.927,3.365 0.563,0.302 10 false ECU 1.698,3.063 2.26,3.365 0.563,0.302 10 false DLC3 1.448,4.76 3.438,5.021 1.99,0.26 10 false : CAN Main Bus Line (CANH) 1.448,5.208 3.438,5.469 1.99,0.26 10 false : CAN Main Bus Line (CANL) 1.458,5.781 3.375,6.01 1.917,0.229 10 false : CAN Branch Line (CANH) 1.448,6.219 3.365,6.479 1.917,0.26 10 false : CAN Branch Line (CANL) 3.427,4.26 4.396,4.552 0.969,0.292 10 false CAN Branch 1.698,3.646 4.021,3.917 2.323,0.271 10 false Open in CAN Branch Line (CANL) 5.802,3.74 7.104,4.177 1.302,0.438 10 false Open in CAN Branch Line (CANH) 4.792,0.177 7.135,0.396 2.344,0.219 10 false Open in CAN Main Bus Line (CANH) 2.719,0.177 3.813,0.427 1.094,0.25 10 false CAN Main Bus

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS or Techstream, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N07
0.49,0.438 0.573,0.438 0.573,0.438 0.906,0.781 true 0.458,1.594 0.552,1.594 0.552,1.594 0.917,1.156 true 0.052,0.333 0.667,0.531 0.615,0.198 10 false CANH 0.031,1.5 0.646,1.698 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.427,0.427 0.719,0.198 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Normal waveform


ii.
C265974N05
1.469,1.479 1.552,1.479 1.552,1.479 1.969,1.104 true 1.521,0.49 1.604,0.49 1.604,0.49 1.969,0.792 true 1.094,0.385 1.708,0.583 0.615,0.198 10 false CANH 1.063,1.385 1.677,1.583 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND 2.688,0.229 3.375,0.406 0.688,0.177 10 false 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N05
1.292,0.917 0.573,0.458 0.573,0.458 0.51,0.458 true 0.469,1.417 0.552,1.417 0.552,1.417 1.063,0.958 true 0.073,0.354 0.688,0.552 0.615,0.198 10 false CANH 0.063,1.323 0.677,1.521 0.615,0.198 10 false CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.344,0.438 0.625,0.208 10 false 1 V/DIV. 2.958,1.354 3.417,1.552 0.458,0.198 10 false GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N05
0.938,0.76 0.583,0.458 0.583,0.458 0.49,0.458 true 0.458,1.552 0.552,1.552 0.552,1.552 0.854,1.146 true 0.063,0.354 0.677,0.552 0.615,0.198 10 false CANH 0.063,1.458 0.677,1.656 0.615,0.198 10 false CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.344,0.448 0.635,0.219 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
C265977N05
0.479,1.406 0.573,1.406 0.573,1.406 0.885,1.125 true 0.5,0.438 0.573,0.438 0.573,0.438 0.833,0.74 true 0.063,0.333 0.677,0.531 0.615,0.198 10 false CANH 0.052,1.302 0.667,1.5 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.417,0.458 0.719,0.229 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
C265978N05
0.49,0.406 0.573,0.406 0.573,0.406 0.938,0.708 true 0.469,1.458 0.552,1.458 0.552,1.458 0.938,1.156 true 0.063,0.302 0.677,0.5 0.615,0.198 10 false CANH 0.063,1.365 0.677,1.563 0.615,0.198 10 false CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.281,0.469 0.583,0.24 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N05
0.458,1.813 0.563,1.813 0.563,1.813 1.083,1.531 true 1.063,1.333 0.573,0.906 0.573,0.906 0.49,0.906 true 0.052,0.802 0.667,1 0.615,0.198 10 false CANH 0.042,1.708 0.656,1.906 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.375,0.479 0.656,0.25 10 false 1 V/DIV. 2.99,1.354 3.385,1.563 0.396,0.208 10 false GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N05
0.458,1.76 0.563,1.76 0.563,1.76 0.948,1.385 true 0.458,0.5 0.552,0.5 0.552,0.5 1.021,0.708 true 0.031,0.406 0.646,0.604 0.615,0.198 10 false CANH 0.052,1.667 0.667,1.865 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.292,0.49 0.594,0.26 10 false 1 V/DIV. 2.969,1.354 3.354,1.604 0.385,0.25 10 false GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

Refer to the Service Bulletin for Data Sending/Receiving Table.


b.

Details of relevant Data List items (Selected system: EFI)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Warm up the engine.


ii.

Turn the A/C switch off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS or Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS or Techstream on.


vii.

Enter the following menus: Powertrain / EFI / Data List.


viii.

According to the display on the GTS or Techstream, read the "Data List".

Powertrain > EFI > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop lamp SW Stop light switch signal ON/OFF
·

ON: Brake pedal is depressed

·

OFF: Brake pedal is released


-
Shift position P range Shift position P signal ON/OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
Shift position R range Shift position R signal ON/OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift position N range Shift position N signal ON/OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
Shift position D range Shift position D signal ON/OFF
·

ON: Shift lever in D

·

OFF: Shift lever not in D


-
Shift position 2 range Shift position 2 signal ON/OFF
·

ON: Shift lever in 2

·

OFF: Shift lever not in 2


-
Shift position L range Shift position L signal ON/OFF
·

ON: Shift lever in L

·

OFF: Shift lever not in L


-
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) 75 to 100°C (167 to 212°F): After warming up engine -
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383.7 rpm 550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
-
Vehicle speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
Main throttle position Absolute No. 1 throttle position sensor Min.: 0%, Max.: 100.0%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


-
Sub throttle position Absolute No. 2 throttle position sensor Min.: 0%, Max.: 100.0%
·

42 to 62%: Accelerator pedal fully released

·

92 to 100%: Accelerator pedal fully depressed


-
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V: Idling -


c.

Details of relevant Data List items (Selected system: A/T)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Warm up the engine.


ii.

Turn the A/C switch off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS or Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS or Techstream on.


vii.

Enter the following menus: Powertrain / A/T / Data List.


viii.

According to the display on the GTS or Techstream, read the "Data List".

Powertrain > A/T > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 25599.6 rpm 650 to 750 rpm: Idling with warm engine, shift lever in N, A/C off -
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
Throttle position Throttle position Min.: 0%, Max.: 100% Actual throttle opening angle -
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V: Idling -
Stop Light Switch Stop light switch signal ON/OFF
·

ON: Brake pedal is depressed

·

OFF: Brake pedal is released


-
Shift SW Status(P) Shift position P signal ON/OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
Shift SW Status(R) Shift position R signal ON/OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift SW Status(N) Shift position N signal ON/OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
Shift SW Status(D) Shift position D signal ON/OFF
·

ON: Shift lever in D

·

OFF: Shift lever not in D


-
Shift SW Status(2) Shift position 2 signal ON/OFF
·

ON: Shift lever in 2

·

OFF: Shift lever not in 2


-
Shift SW Status(L) Shift position L signal ON/OFF
·

ON: Shift lever in L

·

OFF: Shift lever not in L


-
Shift Status Gear position signal N/1st/2nd/3rd/4th/R Actual gear position -


d.

Details of relevant Data List items (Selected system: Meter)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS or Techstream to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS or Techstream on.


vi.

Enter the following menus: Body Electrical > Meter > Data List.


vii.

According to the display on the GTS or Techstream, read the "Data List".

Body Electrical > Meter
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+B voltage value Battery voltage Min.: 0 V, Max.: 25.5 V 11 to 14 V: Idling -
Vehicle speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
Engine RPM Engine speed Min.: 0 rpm, Max.: 12750 rpm 550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
-
Coolant temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up engine -


e.

Details of relevant Data List items (Selected system: ABS/VSC/TRC)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS or Techstream to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS or Techstream on.


vi.

Enter the following menus: Chassis > ABS/VSC/TRC > Data List.


vii.

According to the display on the GTS or Techstream, read the "Data List".

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel speed FR FR Wheel Speed Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) When vehicle is stopped: 0 km/h (0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
-
Wheel speed FL FL Wheel Speed Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) When vehicle is stopped: 0 km/h (0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
-
Wheel speed RR RR Wheel Speed Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) When vehicle is stopped: 0 km/h (0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
-
Wheel speed RL RL Wheel Speed Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) When vehicle is stopped: 0 km/h (0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
-
+IG 1 voltage ECU power supply Min.: 0 V, Max.: 20.00 V 11 to 14 V: Ignition switch ON -
Gear position Gear position information Fail/1st/2nd/3rd/4th/5th/6th/7th/P N/R/Other than R Actual gear position -
Stop lamp SW Stop light switch signal ON/OFF
·

ON: Brake pedal is depressed

·

OFF: Brake pedal is released


-
Meter vehicle speed Vout Vehicle speed Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph) Actual vehicle speed -


f.

Details of relevant Data List items (Selected system: Body)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Turn the ignition switch off.


ii.

Connect the GTS or Techstream to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS or Techstream on.


v.

Enter the following menus: Body Electrical > Body > Data List.


vi.

According to the display on the GTS or Techstream, read the "Data List".

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR wiper HiSW(Main) Front wiper switch (high) signal ON/OFF
·

ON: Front wiper switch to high position

·

OFF: Front wiper switch not to high position


-
+B1 voltage Battery voltage Min.: 0 V, Max.: 20.00 V 11 to 14 V: Ignition switch ON -


g.

Details of relevant Data List items (Selected system: EPS)

HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS or Techstream to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS or Techstream on.


vi.

Enter the following menus: Chassis > EPS > Data List.


vii.

According to the display on the GTS or Techstream, read the "Data List".

Chassis > EPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) When vehicle is stopped: 0 km/h (0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
-
Engine revolution speed Engine speed Min.: 0 rpm, Max.: 12800 rpm 550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
-
IG power supply ECU power supply Min.: 0 V, Max.: 20 V 11 to 14 V: Ignition switch ON -