Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AAC11  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground  P0AAC15  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensors (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A9B11). The battery voltage sensor uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AAC11 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground The inlet air temperature sensor output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

Hybrid battery thermistor

·

Battery voltage sensor

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on
P0AAC15 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The inlet air temperature sensor output voltage is higher than the standard value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

Hybrid battery thermistor

·

Battery voltage sensor

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

HINT:

After checking for the above DTCs, check the hybrid system Data List item "Intake Air Temperature" using the GTS.


Displayed Temperature Malfunction
-45°C (-49°F) or less Open or +B short circuit
95°C (203°F) or more GND short

Related Data List
DTC No. Data List
P0AAC11 Hybrid Battery Cooling Fan Inhaling Air Temperature
P0AAC15

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9B2A.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A9B2A

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.



·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.



·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00, P0AFC96 or P308A12 is not output. A
P0AFC00, P0AFC96 or P308A12 is also output. B


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A376405N08
1.552,1.25 1.896,1.51 0.344,0.26 1.583,1.271 1.865,1.469 0.281,0.198 10 true z12

Check the connections of the z12 battery voltage sensor connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.


Result:
Result
OK
NG



d.

Install the No. 1 hybrid battery exhaust duct.



OK

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR

NG

CONNECT SECURELY

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.
A376406

Visually check the installation condition of the inlet air temperature sensor.

Result:
Result Proceed to
The inlet air temperature sensor is installed in the correct location and its claws are engaged securely. A
The claws of the inlet air temperature sensor are damaged. B
The inlet air temperature sensor is not installed correctly, but its claws are not damaged. C



d.

Install the HV battery junction block assembly.



A

4.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

4.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A368048C08
0.813,2.094 1.219,2.333 0.406,0.24 2.813,2.083 3.219,2.323 0.406,0.24 1.823,2.198 2.01,1.677 true 1.729,2.198 1.813,1.646 true 1.635,2.177 1.615,1.542 true 1.552,2.198 1.396,1.594 true 1.917,2.792 1.813,2.333 true 1.813,3.167 1.729,2.323 true 1.521,3.01 1.646,2.313 true 1.146,3.073 1.552,2.313 true 2.594,2.208 2.781,1.688 true 2.906,3.01 2.594,2.302 true 2.042,1.531 2.5,1.729 0.458,0.198 10 false TC0 1.75,1.469 2.208,1.667 0.458,0.198 10 false TB2 1.5,1.375 1.958,1.573 0.458,0.198 10 false TB1 1.25,1.427 1.708,1.625 0.458,0.198 10 false TB0 1.865,2.875 2.323,3.073 0.458,0.198 10 false GC0 1.688,3.177 2.146,3.375 0.458,0.198 10 false GB2 1.406,3.063 1.865,3.271 0.458,0.208 10 false GB1 1,3.094 1.458,3.302 0.458,0.208 10 false GB0 2.802,1.552 3.292,1.875 0.49,0.323 10 false IGCT 2.833,3.052 3.292,3.25 0.458,0.198 10 false GND 0.927,2.104 1.302,2.458 0.375,0.354 10 false z12 2.896,2.115 3.271,2.469 0.375,0.354 10 false M41 0.115,0.021 0.573,0.219 0.458,0.198 10 false *a
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-1 (TC0) - z12-7 (GC0) Power switch off
0°C (32°F)
26.7 to 27.8 kΩ
z12-1 (TC0) - z12-7 (GC0) Power switch off
25°C (77°F)
9.9 to 10.1 kΩ
z12-1 (TC0) - z12-7 (GC0) Power switch off
40°C (104°F)
5.73 to 5.92 kΩ


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Disconnect the battery voltage sensor connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-1 (TC0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-1 (TC0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-7 (GC0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-7 (GC0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-4 (TB0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-4 (TB0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-10 (GB0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-10 (GB0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-3 (TB1) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-3 (TB1) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-9 (GB1) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-9 (GB1) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-2 (TB2) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-2 (TB2) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-8 (GB2) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-8 (GB2) - M41-5 (GND) Power switch off 10 kΩ or higher



g.

Reconnect the battery voltage sensor connector.


h.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR AND INLET AIR TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR AND INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Check the wire harnesses and connectors of the battery temperature sensors and inlet air temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harnesses and connectors. There are no short circuits to other wire harnesses.


HINT:

As the wire harness of the battery temperature sensors is not available as a supply part, if it cannot be repaired, replace the HV battery.



d.

Install the upper No. 1 hybrid battery cover sub-assembly.


Result:
Proceed to
OK
NG



OK

NG

REPAIR HARNESS OR CONNECTOR (INLET AIR TEMPERATURE SENSOR)