Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Hybrid vehicle control ECU

·

Central gateway ECU (network gateway ECU)

·

Inverter with converter assembly

·

ECM

·

Brake booster with master cylinder assembly

·

No. 5 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for RHD)

·

No. 2 CAN junction connector



WIRING DIAGRAM

for LHD



C366138E02
1.344,0.719 1.958,0.917 0.615,0.198 10 false CANH 1.365,1.25 1.979,1.448 0.615,0.198 10 false CANL 1.844,0.625 2.01,0.823 0.167,0.198 10 false 1 1.875,1.135 2.042,1.333 0.167,0.198 10 false 7 0.427,1.594 1.042,1.792 0.615,0.198 10 false C65 0.438,1.76 2.604,2.01 2.167,0.25 10 false Inverter with Converter Assembly 2.656,0.625 2.99,0.823 0.333,0.198 10 false 10 2.656,1.167 2.99,1.365 0.333,0.198 10 false 21 4.01,0.625 4.344,0.823 0.333,0.198 10 false 8 4,1.167 4.333,1.365 0.333,0.198 10 false 19 4.99,0.635 5.323,0.833 0.333,0.198 10 false 18 4.969,1.167 5.302,1.365 0.333,0.198 10 false 17 5.26,0.635 5.875,0.833 0.615,0.198 10 false CA4H 5.26,1.167 5.875,1.365 0.615,0.198 10 false CA4L 5.927,1 6.542,1.198 0.615,0.198 10 false 120 Ω 5,1.625 5.615,1.823 0.615,0.198 10 false F74 5,1.792 6.99,2.208 1.99,0.417 10 false Central Gateway ECU (Network Gateway ECU) 4,2.76 4.333,2.958 0.333,0.198 10 false 7 3.99,3.302 4.323,3.5 0.333,0.198 10 false 18 2.646,3.302 2.979,3.5 0.333,0.198 10 false 20 2.708,2.76 3.042,2.958 0.333,0.198 10 false 9 1.833,2.75 2.167,2.948 0.333,0.198 10 false 25 1.844,3.302 2.177,3.5 0.333,0.198 10 false 24 1.365,2.865 1.979,3.063 0.615,0.198 10 false CA1H 1.385,3.396 2,3.594 0.615,0.198 10 false CA1L 0.5,3.74 1.115,3.938 0.615,0.198 10 false F3 0.5,3.906 2.417,4.156 1.917,0.25 10 false Hybrid Vehicle Control ECU 2.583,3.771 3.198,3.969 0.615,0.198 10 false F124 2.583,3.948 4.542,4.198 1.958,0.25 10 false No. 5 CAN Junction Connector 4,4.896 4.333,5.094 0.333,0.198 10 false 2 4,5.26 4.333,5.458 0.333,0.198 10 false 13 4,5.698 4.333,5.896 0.333,0.198 10 false 5 3.969,6.219 4.302,6.417 0.333,0.198 10 false 16 2.719,5.688 3.052,5.854 0.333,0.167 10 false 4 2.656,6.229 2.99,6.396 0.333,0.167 10 false 15 1.833,5.698 2.167,5.865 0.333,0.167 10 false 13 1.844,6.208 2.177,6.375 0.333,0.167 10 false 26 1.354,5.698 1.969,5.896 0.615,0.198 10 false CANH 1.375,6.229 1.99,6.427 0.615,0.198 10 false CANL 0.698,6.042 1.313,6.24 0.615,0.198 10 false 120 Ω 1.01,6.885 1.625,7.083 0.615,0.198 10 false ECM 1.021,6.698 1.635,6.896 0.615,0.198 10 false A38 2.677,6.708 3.292,6.906 0.615,0.198 10 false F113 2.677,6.875 4.594,7.125 1.917,0.25 10 false No. 2 CAN Junction Connector 4.99,5.698 5.323,5.896 0.333,0.198 10 false 30 4.979,6.219 5.313,6.417 0.333,0.198 10 false 29 5.25,5.771 5.865,5.969 0.615,0.198 10 false CA2H 5.25,6.344 5.865,6.542 0.615,0.198 10 false CA2L 5.094,6.698 5.708,6.896 0.615,0.198 10 false A39 5.083,6.875 6.781,7.323 1.698,0.448 10 false Brake Booster with Master Cylinder Assembly

for RHD



C366140E03
1.354,0.729 1.969,0.927 0.615,0.198 10 false CA2H 1.396,1.25 2.01,1.448 0.615,0.198 10 false CA2L 1.833,0.604 2.115,0.854 0.281,0.25 10 false 30 1.875,1.167 2.156,1.417 0.281,0.25 10 false 29 2.688,0.615 2.969,0.865 0.281,0.25 10 false 9 2.635,1.146 2.917,1.396 0.281,0.25 10 false 20 4,0.615 4.333,0.781 0.333,0.167 10 false 8 4.01,1.167 4.344,1.333 0.333,0.167 10 false 19 4,1.594 4.333,1.76 0.333,0.167 10 false 7 4,1.948 4.333,2.115 0.333,0.167 10 false 18 2.51,2.385 3.094,2.552 0.583,0.167 10 false F115 2.51,2.552 4.76,2.719 2.25,0.167 10 false No. 4 CAN Junction Connector 4.969,0.635 5.302,0.802 0.333,0.167 10 false 18 4.969,1.177 5.302,1.344 0.333,0.167 10 false 17 5.25,0.635 5.865,0.833 0.615,0.198 10 false CA4H 5.25,1.167 5.865,1.365 0.615,0.198 10 false CA4L 5.906,0.99 6.521,1.188 0.615,0.198 10 false 120 Ω 5.135,1.646 5.75,1.844 0.615,0.198 10 false F74 5.135,1.802 7.083,2.302 1.948,0.5 10 false Central Gateway ECU (Network Gateway ECU) 1.333,3.635 1.948,3.833 0.615,0.198 10 false CANH 1.365,4.167 1.979,4.365 0.615,0.198 10 false CANL 1.854,3.531 2.135,3.781 0.281,0.25 10 false 1 1.854,4.083 2.135,4.25 0.281,0.167 10 false 7 2.677,3.542 2.958,3.708 0.281,0.167 10 false 3 2.625,4.094 2.906,4.26 0.281,0.167 10 false 14 3.99,3.542 4.271,3.708 0.281,0.167 10 false 5 3.969,4.073 4.25,4.24 0.281,0.167 10 false 16 3.99,5.688 4.271,5.854 0.281,0.167 10 false 2 3.969,6.219 4.25,6.385 0.281,0.167 10 false 13 2.667,6.198 2.948,6.365 0.281,0.167 10 false 15 2.708,5.677 2.99,5.844 0.281,0.167 10 false 4 1.833,5.688 2.115,5.854 0.281,0.167 10 false 13 1.854,6.208 2.135,6.375 0.281,0.167 10 false 26 4.969,5.688 5.25,5.854 0.281,0.167 10 false 25 4.969,6.229 5.25,6.396 0.281,0.167 10 false 24 5.26,5.802 5.875,6 0.615,0.198 10 false CA1H 5.25,6.344 5.865,6.542 0.615,0.198 10 false CA1L 5.01,6.667 5.625,6.865 0.615,0.198 10 false F3 5.021,6.844 6.802,7.094 1.781,0.25 10 false Hybrid Vehicle Control ECU 2.583,6.677 3.198,6.875 0.615,0.198 10 false F113 2.583,6.844 4.5,7.094 1.917,0.25 10 false No. 2 CAN Junction Connector 1.01,6.698 1.625,6.896 0.615,0.198 10 false A38 1,6.854 1.5,7.021 0.5,0.167 10 false ECM 0.688,6.063 1.302,6.26 0.615,0.198 10 false 120 Ω 1.354,5.688 1.969,5.885 0.615,0.198 10 false CANH 1.375,6.208 1.99,6.406 0.615,0.198 10 false CANL 0.51,4.531 1.125,4.729 0.615,0.198 10 false C65 0.521,4.698 2.719,4.948 2.198,0.25 10 false Inverter with Converter Assembly 0.5,1.594 1.115,1.792 0.615,0.198 10 false A39 0.5,1.76 2.167,2.208 1.667,0.448 10 false Brake Booster with Master Cylinder Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)

B

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C01
3.333,1.083 3.833,1.333 0.5,0.25 4.083,1.844 4.583,1.583 true 4.5,0.583 3.729,1.844 true 4.583,0.917 3.854,1.844 true 3.969,1.844 4.583,1.25 true 3.708,2.073 4.167,3.083 true 3.844,2.073 4.5,2.917 true 4.094,2.063 4.583,2.25 true 3.969,2.063 4.583,2.583 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.563,0.49 5.479,0.688 0.917,0.198 10 false CANH*b 4.667,0.823 5.583,1.021 0.917,0.198 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 4.667,1.5 5.583,1.698 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F124 4.177,3.135 5.094,3.333 0.917,0.198 10 false CANL*b 4.563,2.906 5.479,3.104 0.917,0.198 10 false CANL*c 4.667,2.542 5.583,2.74 0.917,0.198 10 false CANL*d 4.667,2.219 5.583,2.417 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Hybrid Vehicle Control ECU
*e to Inverter with Converter Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-7 (CANH) - F124-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector
F124-8 (CANH) - F124-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F124-9 (CANH) - F124-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F124-10 (CANH) - F124-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C07
1.417,0.75 1.917,1 0.5,0.25 2.063,1.75 2.5,1.167 true 2.5,2.5 2.052,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F124 2.583,1.052 3.229,1.219 0.646,0.167 10 false CANH*b 2.563,2.5 3.208,2.667 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-8 (CANH) - F124-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F124 No. 5 CAN junction connector.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C02
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.583 3.052,1.844 true 2.667,1.25 3.292,1.844 true 3.479,1.844 2.75,0.917 true 2.75,2.333 3.052,2.063 true 3.333,2.073 2.833,2.667 true 3.469,2.073 3,3 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.083,1.5 3,1.698 0.917,0.198 10 false CANH*b 2.104,1.156 3.021,1.354 0.917,0.198 10 false CANH*c 2.188,0.823 3.104,1.021 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.219,2.313 3.135,2.51 0.917,0.198 10 false CANL*b 2.292,2.615 3.208,2.813 0.917,0.198 10 false CANL*c 2.49,3 3.406,3.198 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to ECM *d to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-2 (CANH) - F113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F113-5 (CANH) - F113-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to ECM) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector.


b.
C366166C08
1.417,0.75 1.917,1 0.5,0.25 1.365,1.75 0.792,1.25 true 0.75,2.49 1.375,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F113 0.208,1.135 0.854,1.302 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C03
3.333,1.083 3.833,1.333 0.5,0.25 4.5,0.583 3.729,1.844 true 4.583,0.917 3.854,1.844 true 3.969,1.844 4.583,1.25 true 3.708,2.073 4.167,3.083 true 3.844,2.073 4.5,2.917 true 3.969,2.063 4.583,2.583 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.563,0.49 5.479,0.688 0.917,0.198 10 false CANH*b 4.667,0.823 5.583,1.021 0.917,0.198 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 4.177,3.135 5.094,3.333 0.917,0.198 10 false CANL*b 4.563,2.906 5.479,3.104 0.917,0.198 10 false CANL*c 4.667,2.542 5.583,2.74 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-7 (CANH) - F115-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F115-9 (CANH) - F115-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
7.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C29
1.417,0.75 1.917,1 0.5,0.25 2.063,1.75 2.427,1.188 true 2.375,2.563 2.042,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.51,0.792 1.906,0.958 0.396,0.167 10 false F115 2.417,0.979 3.063,1.146 0.646,0.167 10 false CANH*b 2.406,2.573 3.052,2.74 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F115 No. 4 CAN junction connector.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C04
3.333,1.083 3.833,1.333 0.5,0.25 3.427,1.833 2.677,0.833 true 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.458,2.073 3.167,3.083 true 3.313,2.073 3,2.833 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*b 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*c 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*d 2.125,0.698 3.042,0.896 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.208,2.313 3.125,2.51 0.917,0.198 10 false CANL*b 2.302,2.563 3.219,2.76 0.917,0.198 10 false CANL*c 2.479,2.854 3.396,3.052 0.917,0.198 10 false CANL*d 2.698,3.125 3.615,3.323 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Inverter with Converter Assembly *d to ECM
*e No. 4 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-2 (CANH) - F113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid Vehicle Control ECU
F113-3 (CANH) - F113-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with Converter Assembly
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F113-5 (CANH) - F113-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 4 CAN Junction Connector



Result:
Result Proceed to
OK A
NG (Line to No. 4 CAN junction connector) B
NG (Line to ECM assembly) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

9.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
9.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector.


b.
C366166C08
1.417,0.75 1.917,1 0.5,0.25 1.365,1.75 0.792,1.25 true 0.75,2.49 1.375,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F113 0.208,1.135 0.854,1.302 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

10.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C02
1.417,0.333 1.917,0.583 0.5,0.25 2.167,1.75 1.771,1.125 true 1.333,1.75 1.667,1.125 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 2.115,1.781 2.594,1.979 0.479,0.198 10 false CA4L 1.042,1.781 1.521,1.979 0.479,0.198 10 false CA4H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR