Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293919 CYLINDER HEAD GASKET A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Remove any oil from the contact surfaces.


b.
A374483C02
1.115,0.583 1.438,0.375 1.438,0.375 1.656,0.375 false 0.521,0.5 0.875,0.5 false 1.719,0.302 2.031,0.458 0.313,0.156 10 false *a 0.865,0 1.177,0.156 0.313,0.156 10 false *b 0.365,1.479 0.677,1.635 0.313,0.156 10 false *c 2.083,0.625 2.396,0.781 0.313,0.156 10 false *a 0.427,2.698 0.74,2.854 0.313,0.156 10 false *c 0.333,0.417 0.646,0.573 0.313,0.156 10 false *d
*a Cylinder Block Sub-assembly
*b 3.0 to 5.0 mm (0.118 to 0.197 in.)
*c 10 to 15 mm (0.394 to 0.591 in.)
*d Diameter 7.0 to 9.0 mm (0.276 to 0.354 in.)
V100135

Front of Engine


Apply seal packing to the cylinder block sub-assembly as shown in the illustration.

NOTICE:

Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes of applying seal packing.



c.
A374484C02
1.427,0.469 1.688,0.208 true 1.74,0.115 2.052,0.271 0.313,0.156 10 false *a
*a Lot No.
V100135

Front of Engine


Place a new cylinder head gasket on the cylinder block sub-assembly as shown in the illustration.

NOTICE:

Make sure to install the cylinder head gasket in the correct direction.



d.
A374485C02
1.021,0.573 1.177,0.25 1.177,0.25 1.354,0.25 false 2.073,0.688 2.385,0.844 0.313,0.156 10 false *a 0.406,1.458 0.719,1.615 0.313,0.156 10 false *b 1.427,0.188 1.74,0.344 0.313,0.156 10 false *a 0.427,2.75 0.74,2.906 0.313,0.156 10 false *b
*a Cylinder Head Gasket
*b Diameter 6 to 8 mm (0.236 to 0.315 in.)
V100135

Front of Engine


Apply seal packing to the cylinder head gasket as shown in the illustration.


Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13750 4.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 5.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 6.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13523G 10.INSTALL CAMSHAFT TIMING SPROCKET

Hide 13050 11.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 12.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13506 13.INSTALL CHAIN SUB-ASSEMBLY

HINT:
·

Be sure to install the chain sub-assembly with the mark plates facing away from the engine assembly.

·

The mark plate on the camshaft side is colored orange.

·

The mark plate on the crankshaft side is colored (yellow or pink).



a.

Temporarily install the crankshaft pulley set bolt to the crankshaft.


b.
A374140

Install the No. 1 chain vibration damper to the cylinder head sub-assembly and cylinder block sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.
A374508C01
2.833,2.135 3.104,1.427 true 1.052,3.573 1.583,3.573 true 0.719,0.323 1.115,0.188 1.115,0.188 1.531,0.188 true 1.573,0.438 0.729,0.438 true 1.49,0.885 0.438,0.885 0.438,0.885 0.438,0.729 true 1.094,0.885 1.094,0.708 true 3.063,1.25 3.375,1.406 0.313,0.156 10 false *a 1.635,3.51 1.948,3.667 0.313,0.156 10 false *b 1.594,0.125 1.906,0.281 0.313,0.156 10 false *c 1.625,0.375 1.938,0.531 0.313,0.156 10 false *d 1.552,0.823 1.865,0.979 0.313,0.156 10 false *e
*a Place the chain sub-assembly on the sprocket
*b Pass the chain sub-assembly through the damper
*c Mark Plate (Orange)
*d Timing Mark (Rectangle)
*e Mark (Circle)


Install the chain sub-assembly with the mark plates (orange) of the chain sub-assembly aligned with the timing mark (rectangle) as shown in the illustration.

HINT:
·

There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).

·

Do not pass the chain sub-assembly around the sprocket of the camshaft timing gear assembly. Only place it on the camshaft timing gear assembly.

·

Pass the chain sub-assembly through the No. 1 chain vibration damper.




d.
A374509

Place the chain sub-assembly on the crankshaft without passing it around the crankshaft.


e.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to align the mark plate (orange) with timing mark, and then install the chain sub-assembly.

A374510C04
2.938,3.083 3.646,1.854 true 5.635,3.125 5.333,1.698 true 3.792,1.74 4.156,1.219 4.156,1.219 3.594,1.615 true 5.573,3.177 5.885,3.333 0.313,0.156 10 false *a 4.146,1.104 4.458,1.26 0.313,0.156 10 false *b 2.813,3.115 3.125,3.271 0.313,0.156 10 false *c
*a Tension the chain sub-assembly *b Mark Plate (Orange)
*c Timing Mark - -


HINT:

If the camshaft timing gear assembly cannot be positioned as shown in the illustration, using a wrench to hold the hexagonal portion of the camshaft, slightly rotate the camshaft timing gear assembly counterclockwise and then install the chain sub-assembly.



f.

Using a wrench to hold the hexagonal portion of the camshaft, slowly turn the camshaft timing gear assembly clockwise to tension the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.

HINT:

Make sure to turn the camshaft timing gear assembly slowly to prevent the camshaft timing sprocket from becoming misaligned.



g.
A374511C01
1.125,1.896 1.906,1.896 true 2.083,1.938 2.865,1.938 true 0.771,1.802 1.083,1.958 0.313,0.156 10 true *a 2.917,1.875 3.229,2.031 0.313,0.156 10 true *b
*a Timing Mark
*b Mark Plate (Yellow or Pink)


Align the mark plate (yellow or pink) with timing mark and install the chain sub-assembly to the crankshaft timing sprocket.


h.

Check that each timing mark is at TDC (compression).

A374512C01
0.24,1.49 0.813,1.49 true 5.49,1.375 6.063,1.375 true 6.188,1.396 6.448,1.396 true 2.198,1.635 2.198,2.438 true 1.188,1.74 1.188,2.552 true 0.594,1.781 0.594,2.552 0.594,2.552 1.51,2.552 true 2.188,0.417 2.188,1.458 true 2.292,0.417 2.292,1.531 true 0.823,1.406 0.823,0.406 0.823,0.406 2.479,0.406 true 2.573,0.333 2.885,0.49 0.313,0.156 10 false *a 6.49,1.323 6.802,1.479 0.313,0.156 10 true *b 5.135,1.313 5.448,1.469 0.313,0.156 10 true *c 0.042,1.417 0.354,1.573 0.313,0.156 10 false *d 1.583,2.479 1.896,2.635 0.313,0.156 10 false *e 2.135,2.469 2.448,2.625 0.313,0.156 10 false *c
*a Mark Plate (Orange) *b Mark Plate (Yellow or Pink)
*c Timing Mark *d Timing Mark (Rectangle)
*e Mark (Circle) - -


HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



i.

Remove the crankshaft pulley set bolt from the crankshaft.


Hide 13562 14.INSTALL NO. 2 CHAIN VIBRATION DAMPER

Hide 13559 15.INSTALL CHAIN TENSIONER SLIPPER

Hide 11302 16.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13540 18.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11193 20.INSTALL SPARK PLUG TUBE GASKET

Hide 11213 21.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 22.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23250 25.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807V 26.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 27.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23818 28.INSTALL FUEL VAPOR FEED PIPE

Hide 17650G 29.INSTALL PURGE VALVE (PURGE VSV)

Hide 1628A 30.INSTALL NO. 6 WATER BY-PASS PIPE

Hide 16289 31.INSTALL NO. 5 WATER BY-PASS PIPE

Hide 11452 32.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15301 33.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 17141 35.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 17167 36.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25620 37.TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

Hide 25610 38.TEMPORARILY INSTALL EGR PIPE ASSEMBLY

Hide 25620 39.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER