Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › PURGE VALVE
RM32K0E _51 Engine / Hybrid System _060064 2ZR-FXE EMISSION CONTROL _0294230 PURGE VALVE A

2ZR-FXE EMISSION CONTROL  PURGE VALVE  INSTALLATION  


PROCEDURE

Hide 17650G 1.INSTALL PURGE VALVE (PURGE VSV)

a.

Install the purge valve (purge VSV) to the No. 3 water by-pass pipe with the screw.

Torque:
3.4 N*m (35 kgf*cm, 30 in.*lbf)


b.

Install the No. 3 water by-pass pipe to the camshaft housing sub-assembly with the bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


c.
A377724C01
1.792,0.948 2.104,0.542 2.104,0.542 2.323,0.542 true 1.365,0.948 1.208,0.354 1.208,0.354 0.979,0.354 true 2.354,0.458 2.552,0.677 0.198,0.219 10 true *1 0.75,0.271 0.969,0.469 0.219,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Connect the No. 2 fuel vapor feed hose to the purge valve (purge VSV).


d.

Connect the No. 1 fuel vapor feed hose to the purge valve (purge VSV).


e.

Connect the purge valve (purge VSV) connector.


Hide 16297 2.CONNECT NO. 9 WATER BY-PASS HOSE

a.
A393943C01
1.271,2.656 1.677,2.854 true 1.083,2.073 1.396,2.229 0.313,0.156 10 false *a 1.615,2.521 1.927,2.677 0.313,0.156 10 false *b 1.729,2.771 2.042,2.927 0.313,0.156 10 false *c 1.5,2.323 1.813,2.479 0.313,0.156 10 false *d 2.313,3.063 2.625,3.219 0.313,0.156 10 false *e
*a Top of Vehicle
*b Left Side of Vehicle
*c Paint Mark
*d 60°
*e 0 to 4 mm (0 to 0.157 in.)


Connect the No. 9 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 16296 3.CONNECT NO. 8 WATER BY-PASS HOSE

a.
A377721C01
2.333,2.406 2.417,2.063 2.417,2.063 2.531,2.063 true 2.229,1.938 2.563,2.115 0.333,0.177 10 false *a 2.813,2.521 3.01,2.771 0.198,0.25 10 false *b 2.573,1.969 2.823,2.219 0.25,0.25 10 false *c 2.125,2.063 2.427,2.292 0.302,0.229 10 false *d 1.198,3.177 1.5,3.406 0.302,0.229 10 false *e
*a Up
*b LH
*c Paint Mark
*d 60°
*e 2 to 7 mm (0.0787 to 0.276 in.)


Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 5.ADD ENGINE COOLANT (for Engine)

Hide 6.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51441 7.INSTALL NO. 1 ENGINE UNDER COVER