Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P26819C  Engine Coolant Bypass Valve Low / Insufficient Flow  


DESCRIPTION

Refer to DTC P268111.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P268111

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P26819C Engine Coolant Bypass Valve Low / Insufficient Flow The actual increase in engine coolant temperature is less than calculated based on the intake air volume (2 trip detection logic).
·

Engine coolant level low

·

Air in cooling system (for Engine)

·

Engine coolant leak

·

Flow shutting valve (water valve)

·

Engine coolant temperature sensor

·

Engine water pump assembly


Does not come on DTC stored SAE Code: P26A3

MONITOR DESCRIPTION

If the actual increase in engine coolant temperature is less than calculated based on the total intake air volume since the engine started, the ECM will judge that the flow shutting valve (water valve) is clogged and store this DTC.

CONFIRMATION DRIVING PATTERN

HINT:

Make sure to perform this procedure when the ambient temperature is 5°C (41°F) or more, the engine coolant temperature between 5 and 40°C (41 and 104°F), and the difference between the engine coolant temperature and ambient temperature is within 10°C (18°F).


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Enter the following menus: Powertrain / Engine / Data List / Coolant Water Route Switching Valve.

10.

Start the engine with A/C switch and all other accessories off, release the accelerator pedal and check that the value of Data List item Engine Coolant Valve is "Closed".

11.

Idle the engine for 2 minutes or more.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P26819C.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P26819C)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P26819C is output A
DTC P26819C and other DTCs are output B


HINT:
·

If DTC P268172 and P26819C are output simultaneously, perform troubleshooting for DTC P26819C first.

·

If DTC P268173 and P26819C are output simultaneously, perform troubleshooting for DTC P268173 first.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P268172

·

If any DTCs other than DTC P268172, P268173 or P26819C are output, perform troubleshooting for those DTCs first.





A

2.CHECK RESERVE SEALED TANK WITHOUT CAP (ENGINE COOLANT LEVEL)

B

2.CHECK RESERVE SEALED TANK WITHOUT CAP (ENGINE COOLANT LEVEL)
a.

Check that the engine coolant level is between the FULL and LOW lines.

OK:

The engine coolant is not excessively low.


HINT:

Make sure that there are no signs of the engine overheating.



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)

NG

3.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
3.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair any engine coolant leaks.

HINT:

Add engine coolant and perform air bleeding after repair.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P26819C)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P26819C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P26819C is output B




A

END

B

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump.

Powertrain > Engine > Active Test
Tester Display
Activate the Electric Water Pump
50004 372 42

e.

Perform the Active Test according to the display on the GTS and lightly squeeze a radiator hose by hand to check for a pulsing feeling.

OK:

Pulsing can be felt in a radiator hose.


HINT:

If pulsing cannot be felt in a radiator hose, inspect the engine water pump assembly. If the impeller is damaged, replace the engine water pump assembly.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (COOLANT TEMPERATURE AND HEATER COOLANT TEMPERATURE SENSOR)

NG

11.INSPECT ENGINE WATER PUMP ASSEMBLY (VISUAL INSPECTION OF IMPELLER)
7.READ VALUE USING GTS (COOLANT TEMPERATURE AND HEATER COOLANT TEMPERATURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Heater Coolant Temperature Sensor.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
Heater Coolant Temperature Sensor
50003 372 205,410

e.

Start the engine.


f.

Read the value displayed on the GTS.

OK:

The values of Data List items Coolant Temperature and Heater Coolant Temperature Sensor change as the engine warms up and do not get stuck on a certain value.


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Result Proceed to
OK A
NG (Value of Data List item Coolant Temperature does not change) B
NG (Value of Data List item Heater Coolant Temperature does not change) C




A

8.REPLACE FLOW SHUTTING VALVE (WATER VALVE)

B

C

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

8.REPLACE FLOW SHUTTING VALVE (WATER VALVE)
a.

Replace the flow shutting valve (water valve).

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>FLOW SHUTTING VALVE>REMOVAL

HINT:

When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P26819C)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P26819C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END

11.INSPECT ENGINE WATER PUMP ASSEMBLY (VISUAL INSPECTION OF IMPELLER)
A375811C02
1.906,1.302 2.552,1.802 2.552,1.802 2.719,1.802 true 0.219,0.146 0.531,0.344 0.313,0.198 10 false *1 2.781,1.729 3.094,1.927 0.313,0.198 10 false *2
*1 Engine Water Pump Assembly
*2 Impeller


a.

Visually inspect the impeller for damage.

OK:

The impeller is not damaged.


HINT:

If the impeller is damaged, replace the engine water pump assembly.

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>WATER PUMP>REMOVAL



Result:
Proceed to
NEXT



NEXT

END