Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P268172  Engine Coolant Bypass Valve Actuator Stuck Open  P268173  Engine Coolant Bypass Valve Actuator Stuck Closed  


DESCRIPTION

Refer to DTC P268111.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P268111

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P268172 Engine Coolant Bypass Valve Actuator Stuck Open The difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 3°C (5°F) or less for 3 seconds or more (2 trip detection logic).
·

Engine coolant level low

·

Air in cooling system (for Engine)

·

Engine coolant leak

·

Flow shutting valve (water valve)

·

Water inlet with thermostat sub-assembly (thermostat)

·

Engine coolant temperature sensor

·

No. 2 engine coolant temperature sensor

·

Engine water pump assembly


Does not come on DTC stored SAE Code: P26AB
P268173 Engine Coolant Bypass Valve Actuator Stuck Closed Either of the following conditions is met for 3 seconds or more (2 trip detection logic):
·

The engine coolant temperature is less than 74°C (165°F) and the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 6°C (11°F) or more.

·

The engine coolant temperature is 74°C (165°F) or more and the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 15.5°C (28°F) or more.


·

Engine coolant level low

·

Air in cooling system (for Engine)

·

Engine coolant leak

·

Flow shutting valve (water valve)

·

Water inlet with thermostat sub-assembly (thermostat)

·

Engine coolant temperature sensor

·

No. 2 engine coolant temperature sensor

·

Engine water pump assembly


Does not come on DTC stored SAE Code: P26B1

MONITOR DESCRIPTION

P268172:

If the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is less than 3°C (5°F) but the target operating state of the flow shutting valve (water valve) is closed, the ECM will determine that the flow shutting valve (water valve) is stuck open and store a DTC.


P268173:

If the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is more than the threshold but the target operating state of the flow shutting valve (water valve) is open, the ECM will determine that the flow shutting valve (water valve) is stuck closed and store a DTC.


CONFIRMATION DRIVING PATTERN

P268172
HINT:

Make sure to perform this procedure when the ambient temperature is 5°C (41°F) or more, the engine coolant temperature between 5 and 40°C (41 and 104°F), and the difference between the engine coolant temperature and ambient temperature is within 10°C (18°F).


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Enter the following menus: Powertrain / Engine / Data List / Coolant Water Route Switching Valve.

10.

Start the engine and check that the value of the Data List item Coolant Water Route Switching Valve is "Close".

11.

Warm up the engine until the value of the Data List item Coolant Water Route Switching Valve is "Open".

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P268172.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.





P268173
HINT:

When performing this procedure, start the engine when the coolant temperature is less than 40°C (104°F).


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

10.

Start the engine.

11.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P268173.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.





CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P268172 OR P268173)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P268172 or P268173 is output A
DTC P268172 or P268173 and other DTCs are output B


HINT:
·

If DTC P268173 and P26819C are output simultaneously, perform troubleshooting for DTC P268173 first.

·

If DTC P268172 and P26819C are output simultaneously, perform troubleshooting for DTC P26819C first.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P26819C

·

If any DTCs other than DTC P268172, P268173 or P26819C are output, perform troubleshooting for those DTCs first.





A

2.CHECK RESERVE SEALED TANK WITHOUT CAP (ENGINE COOLANT LEVEL)

B

2.CHECK RESERVE SEALED TANK WITHOUT CAP (ENGINE COOLANT LEVEL)
a.

Check that the engine coolant level is between the FULL and LOW lines.

OK:

The engine coolant is not excessively low.


HINT:

Make sure that there are no signs of the engine overheating.



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)

NG

3.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
3.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair any engine coolant leaks.

HINT:

Add engine coolant and perform air bleeding after repair.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P268172 OR P268173)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P268172 OR P268173)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P268172 or P268173 is output B




A

END

B

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump.

Powertrain > Engine > Active Test
Tester Display
Activate the Electric Water Pump
50004 372 42

e.

Perform the Active Test according to the display on the GTS and lightly squeeze a radiator hose by hand to check for a pulsing feeling.

OK:

Pulsing can be felt in a radiator hose.


HINT:

If pulsing cannot be felt in a radiator hose, inspect the engine water pump assembly. If the impeller is damaged, replace the engine water pump assembly.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (COOLANT TEMPERATURE AND HEATER COOLANT TEMPERATURE SENSOR)

NG

14.INSPECT ENGINE WATER PUMP ASSEMBLY (VISUAL INSPECTION OF IMPELLER)
7.READ VALUE USING GTS (COOLANT TEMPERATURE AND HEATER COOLANT TEMPERATURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Heater Coolant Temperature Sensor.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
Heater Coolant Temperature Sensor
50003 372 205,410

e.

Start the engine.


f.

Read the value displayed on the GTS.

OK:

The values of Data List items Coolant Temperature and Heater Coolant Temperature Sensor change over time and do not get stuck on a certain value.


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Result Proceed to
OK A
NG (Value of Data List item Coolant Temperature does not change) B
NG (Value of Data List item Heater Coolant Temperature does not change) C




A

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN)

B

C

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up with the A/C switch and all other accessories off until the engine coolant temperature reaches 85°C (185°F).

HINT:

Warm up the engine until the engine coolant temperature reaches the water inlet with thermostat sub-assembly opening temperature.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan / Data List / Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the Engine Cooling Fan
Data List Display
Coolant Temperature
50004 372 26 205

g.

Read the Data List while performing the Active Test with the engine idling.

OK:

The engine coolant temperature does not decrease to 70°C (158°F) or less.


HINT:

While performing the Active Test, if the engine coolant temperature decreases to 70°C (158°F) or less, the water inlet with thermostat sub-assembly may be stuck open.



Result:
Control the Engine Cooling Fan
(Active Test)
Coolant Temperature
(Data List)
Water Inlet with Thermostat Sub-assembly Operation Proceed to
High Higher than 70°C (158°F) Normal A
70°C (158°F) or less Stuck open B



A

9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

CHECK AND REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:
·

If the result of the engine coolant temperature sensor inspection differs greatly from the specified value, inspect the water inlet with thermostat sub-assembly.

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

NG

10.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the No. 2 engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.REPLACE FLOW SHUTTING VALVE (WATER VALVE)

NG

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

11.REPLACE FLOW SHUTTING VALVE (WATER VALVE)
a.

Replace the flow shutting valve (water valve).

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>FLOW SHUTTING VALVE>REMOVAL

HINT:

When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P268172 OR P268173)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P268172 OR P268173)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END

14.INSPECT ENGINE WATER PUMP ASSEMBLY (VISUAL INSPECTION OF IMPELLER)
A375811C02
1.906,1.302 2.552,1.802 2.552,1.802 2.719,1.802 true 0.219,0.146 0.531,0.344 0.313,0.198 10 false *1 2.781,1.729 3.094,1.927 0.313,0.198 10 false *2
*1 Engine Water Pump Assembly
*2 Impeller


a.

Visually inspect the impeller for damage.

OK:

The impeller is not damaged.


HINT:

If the impeller is damaged, replace the engine water pump assembly.

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>WATER PUMP>REMOVAL



Result:
Proceed to
NEXT



NEXT

END