Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A4/32  Open or Short in Release Switch Circuit  C13AC/34  Release Switch Circuit  


DESCRIPTION

When the electric parking brake switch (electric parking brake switch assembly) is pushed to the release side, a release request signal is sent to the parking brake ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A4/32 Open or Short in Release Switch Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off.

2.

Terminal REL1 voltage is less than 1.5 V* or more than 9.4 V*; or terminal REL2 voltage is less than 1.5 V* or more than 9.4 V*

3.

Problem occurs for approximately 1 second.


HINT:

*: When auxiliary battery voltage is 12 V


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.
C13AC/34 Release Switch Circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off.

2.

ON/OFF judgment of release switch 1 and release switch 2 does not match for approximately 1 second.


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C13A4/32
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status Terminal REL1 voltage is less than 1.5 V* ○ - - -
Terminal REL1 voltage is more than 9.4 V* - ○ - -
Terminal REL2 voltage is less than 1.5 V* - - ○ -
Terminal REL2 voltage is more than 9.4 V* - - - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions: C13A4/32
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off ○ ○ ○ ○
Malfunction Status Terminal REL1 voltage is less than 1.5 V* ○ - - -
Terminal REL1 voltage is more than 9.4 V* - ○ - -
Terminal REL2 voltage is less than 1.5 V* - - ○ -
Terminal REL2 voltage is more than 9.4 V* - - - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

*: When auxiliary battery voltage is 12 V



DTC Detection Conditions: C13AC/34
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off - ○
Malfunction Status ON/OFF judgment of release switch 1 and release switch 2 does not match ○ ○
Detection Time Approximately 1 second Approximately 1 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When the electric parking brake switch (electric parking brake switch assembly) is not fully pushed and held to the release side for 1 second or more, only 1 of 2 internal contacts may contact causing a DTC to be stored. This is not a malfunction.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (electric parking brake switch assembly), as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the M71 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M71-19 (REL1) - F67-5 (RLS1) Always Below 5 Ω
M71-16 (REL2) - F67-4 (RLS2) Always Below 5 Ω
M71-19 (REL1) or F67-5 (RLS1) - Body ground Always 10 kΩ or higher
M71-16 (REL2) or F67-4 (RLS2) - Body ground Always 10 kΩ or higher
F67-2 (GND1) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Push the electric parking brake switch (electric parking brake switch assembly) to the release side.

HINT:

When the electric parking brake switch (electric parking brake switch assembly) is not fully pushed and held to the release side for 1 second or more, only 1 of 2 internal contacts may contact causing a DTC to be stored. This is not a malfunction.



e.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE PARKING BRAKE ECU ASSEMBLY

B