Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE UNIT › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0298014 ENGINE UNIT A

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired

·

Replacement of knock sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

PROCEDURE

Hide 16331 1.REMOVE WATER OUTLET

a.
A378473C02
0.583,1.573 0.771,1.573 0.771,1.573 0.948,1.25 true 2.938,1.354 3.26,0.229 3.26,0.229 3.083,0.229 true 2.708,1.969 2.594,1.969 2.594,1.969 2.531,1.708 true 0.344,1.521 0.563,1.688 0.219,0.167 10 true *1 2.875,0.177 3.094,0.344 0.219,0.167 10 false *3 2.781,1.906 3.031,2.073 0.25,0.167 10 true *2
*1 No. 9 Water By-pass Hose
*2 No. 7 Water by-pass Hose
*3 No. 4 Water By-pass Hose


Slide the clip and disconnect the No. 7 water by-pass hose from the No. 2 water by-pass hose.


b.

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR valve assembly with EGR cooler.


c.

Slide the clip and disconnect the No. 9 water by-pass hose from the purge valve.


d.

Remove the 2 nuts, water outlet and water outlet gasket from the cylinder head sub-assembly.


Hide 25610 2.REMOVE EGR PIPE ASSEMBLY

a.
A378474

Remove the 4 bolts and EGR pipe assembly, EGR pipe gasket and inlet EGR gasket.


Hide 25601L 3.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

a.
A372584C01
0.958,1.427 1.208,1.656 0.25,0.229 10 true *a 1.51,1.875 1.76,2.063 0.25,0.188 10 true *a
V100135

Bolt
V100136

Nut
*a Stud bolt


Remove the bolt and 4 nuts.


b.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and EGR valve assembly with EGR cooler from the cylinder head sub-assembly and exhaust manifold (TWC: Front Catalyst).


c.

Remove the EGR cooler gasket.


Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 6.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 15301 9.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 10.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16289 11.REMOVE WATER BY-PASS PIPE NO.5

a.
A372586

Slide the clip and disconnect the No. 5 water by-pass pipe from the timing chain cover sub-assembly.


b.

Remove the 2 bolts and No. 5 water by-pass pipe from the cylinder block sub-assembly.


Hide 1628A 12.REMOVE NO. 6 WATER BY-PASS PIPE

a.
A372587

Slide the clip and disconnect the No. 6 water by-pass pipe from the water inlet sub-assembly.


b.

Remove the 2 bolts and No. 6 water by-pass pipe from the cylinder head sub-assembly.


Hide 17650G 13.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 14.REMOVE FUEL VAPOR FEED PIPE

a.
A372582

Remove the 2 bolts and fuel vapor feed pipe from the cylinder head cover sub-assembly.


Hide 23807 15.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 16.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 17.REMOVE FUEL INJECTOR ASSEMBLY

Hide 12261 18.REMOVE VENTILATION HOSE

a.
A372583

Slide the clip and remove the ventilation hose from the PCV valve (ventilation valve sub-assembly).


Hide 20.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A394347

Remove the bolt and wire harness clamp bracket from the timing chain cover sub-assembly.