Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0301367 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E360348E01
0.427,4.563 4.708,4.76 4.281,0.198 10 false Steering Pad Switch Assembly 2.781,4.146 4.24,4.615 1.458,0.469 10 false Spiral Cable with Sensor Sub-assembly 0.531,0.615 4.813,0.813 4.281,0.198 10 false from TAIL Relay 3.427,0.802 4.063,0.99 0.635,0.188 10 false PANEL 6.021,3.604 6.656,3.792 0.635,0.188 10 false SWG 6.021,2.469 6.656,2.656 0.635,0.188 10 false ILL+ 3.156,3.479 3.792,3.667 0.635,0.188 10 false EAU 3.167,2.354 3.802,2.542 0.635,0.188 10 false IL+2 5.594,2.469 6.229,2.656 0.635,0.188 10 false F126 5.583,3.615 6.219,3.802 0.635,0.188 10 false F125 3.719,3.604 4.354,3.792 0.635,0.188 10 false F29 3.74,2.469 4.375,2.656 0.635,0.188 10 false F29 2.708,2.458 3.344,2.646 0.635,0.188 10 false z1 2.708,3.594 3.344,3.781 0.635,0.188 10 false z1 5.667,3.406 6.302,3.594 0.635,0.188 10 false 23 5.667,2.26 6.302,2.448 0.635,0.188 10 false 10 3.771,2.25 4.406,2.438 0.635,0.188 10 false 13 3.813,3.406 4.448,3.594 0.635,0.188 10 false 3 2.729,2.26 3.365,2.448 0.635,0.188 10 false 5 2.75,3.396 3.385,3.583 0.635,0.188 10 false 8 0.875,3.594 1.51,3.781 0.635,0.188 10 false RH 0.865,2.844 1.5,3.031 0.635,0.188 10 false LH 5.854,4.49 7.156,5.063 1.302,0.573 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the spiral cable with sensor sub-assembly connector.


b.
E360342C01
1.49,0.427 1.917,0.677 0.427,0.25 2.229,1.719 1.979,1.344 true 2.177,1.729 2.792,1.927 0.615,0.198 10 false IL+2 1.573,0.479 2.188,0.677 0.615,0.198 10 false F29 0.115,0.135 0.729,0.333 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F29-13 (IL+2) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSPECTION


c.

Check that the steering pad switch assembly illumination illuminates.

OK:

The steering pad switch assembly illumination illuminates.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.
E360341C02
1.479,0.427 1.927,0.667 0.448,0.24 2.333,1.667 2.167,1.323 true 2.344,1.698 2.958,1.896 0.615,0.198 10 false ILL+ 1.531,0.469 1.99,0.667 0.458,0.198 10 false F126 0.104,0.115 0.563,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-10 (ILL+) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR