Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
89831A
1.INSTALL NO. 1 SIDE AIRBAG SENSOR
Check that the power switch off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.
| *a | Correct | *b | Incorrect |
Connect the connector to the No. 1 side airbag sensor.
| *a | White Housing Lock | *b | Connect |
When connecting any airbag connector, take care not to damage the airbag wire harness.
Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.
Engage the claw to install the No. 1 side airbag sensor with the bolt.
If the No. 1 side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the No. 1 side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the No. 1 side airbag sensor claw is securely inserted into the body hole.
Check that there is no looseness in the installed parts of the No. 1 side airbag sensor.
89831E
2.INSTALL FLOOR SIDE AIRBAG SENSOR
Check that the power switch off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Connect the connector to the floor side airbag sensor.
| *a | White Housing Lock | *b | Connection is completed |
When connecting any airbag connector, take care not to damage the airbag wire harness.
Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).
When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.
Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.
| *a | Incorrect | *b | Correct |
Engage the claw to install the floor side airbag sensor with the bolt.
If the floor side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the floor side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the floor side airbag sensor claw is securely inserted into the body hole.
Check that there is no looseness in the installed parts of the floor side airbag sensor.
62414A
3.INSTALL CENTER PILLAR LOWER GARNISH
62332A
4.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
67918A
5.INSTALL REAR DOOR SCUFF PLATE
62312B
6.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
67914
7.INSTALL FRONT DOOR SCUFF PLATE
73220
8.CONNECT FRONT SEAT OUTER BELT ASSEMBLY
73233
9.INSTALL LAP BELT OUTER ANCHOR COVER
10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
11. PERFORM DIAGNOSTIC SYSTEM CHECK
12.INSPECT SRS WARNING LIGHT