Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304181 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75752C 1.INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING

a.

Using an air riveter or hand riveter with a nose piece, install the front door front window frame moulding with 2 new rivets.

B458700

NOTICE:

To prevent damage, when installing the front door front window frame moulding, make sure that there are enough people available to hold it securely.


HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C11
1.292,0.281 1.438,0.281 1.438,0.281 1.781,0.74 false 1.875,1.271 1.875,1.823 false 1.125,0.208 1.438,0.365 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C10
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




b.
B458698C01
2.76,0.698 2.167,0.25 2.167,0.25 2.729,0.365 true 0.885,3.167 1.333,2.75 1.333,2.75 0.844,2.583 true 3.167,2.302 2.969,2.188 true 1.969,0.156 2.281,0.354 0.313,0.198 10 false *a 1.406,2.656 1.719,2.854 0.313,0.198 10 false *a 2.729,2.073 2.896,2.24 0.167,0.167 10 true *b
*a Bolt <A>
*b Bolt <B>


Install the front door panel sub-assembly with the 4 bolts <A>.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

NOTICE:

To prevent damage, when installing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.



c.

Apply adhesive to the threads of the bolt <B>.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the bolt <B>.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.
B435280C01
2.365,0.958 2.708,0.958 true 1.865,2.948 2.208,2.948 true 1.26,3.479 0.563,2.823 0.563,2.823 1.26,2.427 false 1.813,4.323 1.813,4.448 true 2.208,4.208 2.563,4.042 true 1.229,1.563 0.615,1.01 0.615,1.01 1.01,0.51 false 0.448,3.979 0.823,4.229 0.375,0.25 12 false *A 2.76,0.875 3.073,1.031 0.313,0.156 10 false *1 2.26,2.875 2.573,3.031 0.313,0.156 10 false *2 1.729,4.458 2.042,4.615 0.313,0.156 10 false *a 2.625,3.969 2.938,4.125 0.313,0.156 10 false *b 0.365,2.75 0.677,2.906 0.313,0.156 10 false *b 0.406,0.927 0.719,1.083 0.313,0.156 10 false *b
*A Section
*1 Front Door Upper Hinge Assembly
*2 Front Door Lower Hinge Assembly
*a Front Door Hinge Assembly
*b Anti-rust Coating


Using a brush, apply anti-rust coating to each front door hinge assembly as shown in the illustration.


f.

Connect each connector.


g.

Engage each clamp.


Hide 62112 2.INSTALL COWL SIDE TRIM BOARD

Hide 67914 3.INSTALL FRONT DOOR SCUFF PLATE

Hide 75754A 4.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

a.

Engage the guide to temporarily install the front door upper window frame moulding to the door frame.

B458701


b.

Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 6 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C11
1.292,0.281 1.438,0.281 1.438,0.281 1.781,0.74 false 1.875,1.271 1.875,1.823 false 1.125,0.208 1.438,0.365 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C10
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 68126 5.INSTALL FRONT DOOR FIX WINDOW GLASS

Hide 67402F 6.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Hide 68151C 7.INSTALL FRONT DOOR GLASS RUN

Hide 67664 8.INSTALL DOOR FRAME UPPER GARNISH

Hide 67862 9.CONNECT FRONT DOOR WEATHERSTRIP

a.

Engage the clips to connect the front door weatherstrip.


Hide 75072A 10.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When installing a new front door outside moulding sub-assembly, heat the vehicle body and front door outside moulding sub-assembly using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Door Outside Moulding Sub-assembly 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or front door outside moulding sub-assembly excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B458702C01
1.833,1.406 2.167,1.74 true 2.25,1.646 2.563,1.802 0.313,0.156 10 false *a
*a Double-sided Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install a new front door outside moulding sub-assembly.

i.

Using a heat light, heat the vehicle body and front door outside moulding sub-assembly.


ii.

Remove the release paper from the front door outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the guide and clip and attach the double-sided tape and caulking sponge to install the front door outside moulding sub-assembly.

HINT:

Press the front door outside moulding sub-assembly firmly to install it.




c.

Remove the protective tape.


Hide 75720 11.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY