The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
*1: When performing learning using the GTS.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69284C
3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
|
Remove in this Direction |
Using a moulding remover A, disengage the claws to remove the front door inside handle bezel plug as shown in the illustration.
74232
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
|
Remove in this Direction |
Disengage the claws, clips and guides as shown in the illustration.
Disconnect the 2 connectors to remove the multiplex network master switch assembly with front armrest base upper panel.
74231
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
|
Remove in this Direction |
Disengage the claws, clips and guides as shown in the illustration.
Disconnect the connector to remove the power window regulator switch assembly with front armrest base upper panel.
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Remove the 3 screws.
| *a | Clip (A) |
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips (A), other clips and guide as shown in the illustration.
|
Remove in this Direction |
Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip and front door belt seal as shown in the illustration.
w/ Illumination:
Disconnect the connector.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Remove in this Direction |
Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.
69206B
7.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the claw and guides to remove the front door inside handle sub-assembly.
81080S
8.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Illumination)
67492A
9.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the clips to remove the front door lower frame bracket garnish.
68172A
10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction |
Disengage the claws remove the front door glass inner weatherstrip with the front door belt seal as shown in the illustration.
68195
11.REMOVE FRONT DOOR BELT SEAL
|
Remove in this Direction |
Remove the front door belt seal from the front door glass inner weatherstrip as shown in the illustration.
67838A
12.REMOVE FRONT DOOR VENT SEAL
Remove the front door vent seal.
87940
13.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
87912A
14.REMOVE OUTER MIRROR PROTECTOR
|
Remove in this Direction |
Remove the 2 screws.
Disengage the claws to remove the outer mirror protector as shown in the illustration.
67832
15.REMOVE FRONT DOOR SERVICE HOLE COVER
Turn the 3 door weatherstrip clips 45° and remove it clips as shown in the illustration.
Disengage the clips to remove the front door service hole cover.
89835
16.REMOVE DOOR SIDE AIRBAG SENSOR
68102
17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
for Driver Side:
Connect the multiplex network master switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass sub-assembly to fall.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
67831C
18.REMOVE NO. 2 FRONT DOOR SERVICE HOLE COVER
Disengage the claws to remove the No. 2 front door service hole cover.
19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
| *a | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.
Remove the 5 bolts and front door window regulator sub-assembly.
Remove the temporary bolt from the front door window regulator assembly.
67664
20.REMOVE DOOR FRAME UPPER GARNISH
Disengage the guides to remove the door frame upper garnish.
68151C
21.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67402F
22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Raise up the front door weatherstrip.
Remove the screw.
Remove the 2 bolts and front door front lower frame sub-assembly.
Install the front door weatherstrip.
67404F
23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction |
Remove the bolt.
Disengage the guide to remove the front door rear lower frame sub-assembly as shown in the illustration.
69217D
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
| *1 | Hole Plug |
|
Remove in this Direction |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Remove the front door outside handle cover with front door lock cylinder assembly as shown in the illustration.
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and guides to remove the front door outside handle cover as shown in the illustration.
69217D
25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
| *1 | Hole Plug |
|
Remove in this Direction |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws to remove the front door outside handle cover as shown in the illustration.
69220
26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
| *a | Protective Tape |
w/ Entry and Start System:
Disengage the claws.
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
|
Remove in this Direction |
Remove the front door outside handle assembly as shown in the illustration.
69241H
27.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
|
Remove in this Direction |
Disengage the claws and guide to remove the front door front outside handle pad as shown in the illustration.
69242E
28.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
|
Remove in this Direction |
Disengage the guides to remove the front door rear outside handle pad as shown in the illustration.
69040A
29.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69202A
30.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Entry and Start System:
| *a | Grommet |
| *b | Guide |
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the grommet and guides to separate the front door outside handle frame sub-assembly as shown in the illustration.
| *a | Guide |
| *b | Clamp |
Disengage the clamps and guide to remove the front door outside handle frame sub-assembly.
w/o Entry and Start System:
| *a | Grommet |
| *b | Guide |
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the grommet and guides to remove the front door outside handle frame sub-assembly as shown in the illustration.
w/ Protector:
Remove the 3 screws and door outside handle protector.
69312
31.REMOVE FRONT DOOR LOCK OPEN ROD
| *a | Snap |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the snap to remove the front door lock open rod from the front door outside frame sub-assembly as shown in the illustration.
68610
32.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
67862
33.REMOVE FRONT DOOR WEATHERSTRIP
| *a | Clip (A) |
Using a clip remover, disengage the clip (A) and other clips to remove the front door weatherstrip.
67837B
34.REMOVE FRONT DOOR DUST PROOF SEAL
Remove the 3 front door dust proof seals.
86160
35.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (w/ Speaker)
86262E
36.REMOVE FRONT SPEAKER COVER (w/o Speaker)
Disconnect the connector.
Using a drill bit with a diameter of less than 5 mm (0.197 in.), drill out the 3 rivet heads.
Do not drill the rivet at an angle as this will cause damage to the drill and rivet installation hole. Line up the drill with the rivet, and carefully drill out the rivet head.
Be careful as the drilled rivet will be very hot.
Continue drilling and push out the remaining rivet fragments.
Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.
Disengage the claw and guide to remove the front speaker cover.
68126
37.REMOVE FRONT DOOR FIX WINDOW GLASS
|
Remove in this Direction |
Remove the front door fix window glass with front door fix window weatherstrip as shown in the illustration.
68216
38.REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP
Remove the front door fix window weatherstrip from the front door fix window glass.
67001A
39.REMOVE FRONT DOOR PANEL CUSHION
Using a clip remover, disengage the claws to remove the 2 front door panel cushions.
75732A
40.REMOVE FRONT DOOR OUTSIDE MOULDING
75788A
41.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
42.REMOVE HOLE CAP
Remove the hole cap.
75720
43.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
67914
44.REMOVE FRONT DOOR SCUFF PLATE
62112
45.REMOVE COWL SIDE TRIM BOARD
75752C
46.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING
75754A
47.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
75966B
48.REMOVE NO. 4 FRONT DOOR STRIPE
75986G
49.REMOVE FRONT DOOR OUTSIDE STRIPE
75976G
50.REMOVE NO. 2 FRONT DOOR STRIPE