Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304573 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Steering Pad Switch Circuit  


DESCRIPTION

The forward recognition camera receives a Lane Departure Alert Main Switch signal from the steering pad switch assembly.

WIRING DIAGRAM

C367184E02
0.906,0.865 1.396,1.115 0.49,0.25 10 false 240Ω 0.49,1.51 1.792,2 1.302,0.49 10 false Lane Departure Alert Main Switch 0.146,2.521 2.146,2.823 2,0.302 10 false Steering Pad Switch Assembly 2.063,0.521 2.281,0.708 0.219,0.188 10 false 4 2.031,0.708 2.25,0.896 0.219,0.188 10 false z1 2.031,1.323 2.25,1.51 0.219,0.188 10 false z1 2.052,1.115 2.271,1.302 0.219,0.188 10 false 7 3.198,0.51 3.458,0.708 0.26,0.198 10 false 12 3.156,0.719 3.479,0.938 0.323,0.219 10 false F29 3.167,1.323 3.49,1.542 0.323,0.219 10 false F29 3.24,1.125 3.458,1.313 0.219,0.188 10 false 2 2.771,0.615 3.094,0.833 0.323,0.219 10 false DIST 2.781,1.219 3.104,1.438 0.323,0.219 10 false ECC 5.26,0.625 5.479,0.813 0.219,0.188 10 false 3 5.438,0.667 6.052,0.927 0.615,0.26 10 false LKSW 2.167,1.833 3.271,2.219 1.104,0.385 10 false Spiral Cable Sub-assembly 5.188,1.385 5.469,1.583 0.281,0.198 10 false R5 5.198,1.573 7.042,1.906 1.844,0.333 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F29-12 (DIST) - R5-3 (LKSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F29-12 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F29 spiral cable sub-assembly connector.


Result:
Result Proceed to
OK A
NG B



A

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F29-2 (ECC) - Body ground Always Below 1 Ω



c.

Reconnect the F29 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR