When the seat heater switch on air conditioning control assembly is operated, the seat heater control sub-assembly RH receives the signal. The seat heater control sub-assembly RH receives the signal and operates the front seat heater.
If the auxiliary battery voltage is low, the seat heater system may not operate. Refer to Data List for the power steering system.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST
Inspect the fuses for circuits related to this system before performing the following procedure.
Clear the DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
DTC B14B5 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH) |
Disconnect the seat heater control sub-assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Y4-8 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y4 seat heater control sub-assembly RH connector.
Disconnect the Y2 front seat cushion heater assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y4-1 (HTR1) - Y2-1 | Always | Below 1 Ω |
| Y4-6 (THR+) - Y2-4 | Always | Below 1 Ω |
| Y4-11 (THR-) - Y2-5 | Always | Below 1 Ω |
| Y4-7 (E) - Y2-6 | Always | Below 1 Ω |
| Y2-2 - Body ground | Always | Below 1 Ω |
| Y4-1 (HTR1) or Y2-1 - Body ground | Always | 10 kΩ or higher |
| Y4-6 (THR+) or Y2-4 - Body ground | Always | 10 kΩ or higher |
| Y4-11 (THR-) or Y2-5 - Body ground | Always | 10 kΩ or higher |
| Y4-7 (E) or Y2-6 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat cushion heater assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER>REMOVAL
Inspect the front seat cushion heater assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seatback heater assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER>REMOVAL
Inspect the front seatback heater assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F61 seat heater switch (air conditioning control assembly) connector.
Disconnect the Y4 seat heater control sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F61-11 (SW) - Y4-3 (SWR) | Always | Below 1 Ω |
| F61-4 (RV) - Y4-4 (VOL) | Always | Below 1 Ω |
| F61-11 (SW) or Y4-3 (SWR) - Body ground | Always | 10 kΩ or higher |
| F61-4 (RV) or Y4-4 (VOL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the heater control sub-assembly RH with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the seat heater system is operated normally.
The seat heater system is operated normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seat heater switch (air conditioning control assembly) with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the seat heater system is operated normally.
The seat heater system is operated normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG