Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _062271 SEAT BELT _0303947 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.


Hide 67918A 5.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 73233 7.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B460521C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guide to remove the lap belt outer anchor cover as shown in the illustration.


Hide 73220 8.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B458418

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62414A 9.REMOVE CENTER PILLAR LOWER GARNISH

Hide 62420A 10.REMOVE CENTER PILLAR GARNISH ASSEMBLY

Hide 73220 11.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B458419

Remove the nut to disconnect the shoulder anchor of the front seat outer belt assembly.


b.

for TMMT Made:

i.
B458420C01
1.052,0.323 1.281,0.458 true 0.625,0.979 0.875,0.781 true 1.323,0.438 1.635,0.635 0.313,0.198 10 false *a 0.458,0.948 0.771,1.146 0.313,0.198 10 false *b
*a Protective Tape
*b Locking Button


Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.



c.

except TMMT Made:

i.
B460471C01
0.542,0.906 0.823,0.729 true 0.521,0.531 0.75,0.469 true 0.344,0.833 0.656,1.031 0.313,0.198 10 false *b 0.333,0.469 0.646,0.667 0.313,0.198 10 false *a
*a Protective Tape
*b Locking Button


Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.



d.
B458421

Remove the bolt.


e.

Disengage the guides to remove the front seat outer belt assembly.


Hide 73200A 12.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B458422

Remove the 2 bolts.


b.

Disengage the guide to remove the front shoulder belt anchor adjuster assembly.