Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300406 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during condenser removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Audio and Visual System).

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Navigation System (for Radio and Display Type)).



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.REMOVE HEADLIGHT ASSEMBLY LH (for Single Beam Headlight)

Hide 3.REMOVE HEADLIGHT ASSEMBLY RH (for Single Beam Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE HEADLIGHT ASSEMBLY LH (for Triple Beam Headlight)

Hide 5.REMOVE HEADLIGHT ASSEMBLY RH (for Triple Beam Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 52029A 6.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

Hide 53117C 7.REMOVE NO. 1 RADIATOR GRILLE RETAINER

Hide 16561C 8.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53510 10.REMOVE HOOD LOCK ASSEMBLY

Hide 17752 11.REMOVE NO. 2 AIR CLEANER INLET (for 2ZR-FXE)

Hide 53205 12.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 16594 13.REMOVE NO. 2 RADIATOR AIR GUIDE

Hide 52611 14.REMOVE FRONT BUMPER ENERGY ABSORBER

Hide 52131A 15.REMOVE FRONT BUMPER REINFORCEMENT

Hide 16595B 16.REMOVE NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 17.REMOVE NO. 1 RADIATOR AIR GUIDE RH

Hide 88703 18.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
I112407

Remove the bolt to disconnect the discharge hose sub-assembly from the cooler condenser assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 19.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A

a.

While pressing the end of the cooler refrigerant liquid pipe A into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

E336869C02
3.125,3.042 3.75,3.365 3.75,3.365 3.24,2.792 true 4.625,2.688 4.625,2.104 false 5.865,2.688 5.865,2.271 false 4.573,2.75 4.885,2.906 0.313,0.156 10 false *1 5.813,2.74 6.125,2.896 0.313,0.156 10 false *2 3.781,3.302 3.979,3.448 0.198,0.146 10 true *3 4.646,0.813 4.958,0.969 0.313,0.156 10 false *a
*1 Cooler Refrigerant Liquid Pipe A *2 Cooler Condenser Assembly
*3 Piping Clamp - -
*a Press In - -


NOTICE:
·

If any foreign matter is adhered to the connecting part, brush it off or use compressed air to remove it.

·

Make sure that fragments of the piping clamp do not enter the piping.




b.

Disconnect the cooler refrigerant liquid pipe A.

NOTICE:

Clean off any foreign matter near the ends of the cooler refrigerant liquid pipe A and cooler condenser assembly.



c.

Remove the 2 O-rings from the cooler refrigerant liquid pipe A.

NOTICE:

Wrap the open ends of the separated cooler condenser assembly and cooler refrigerant liquid pipe A with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88460 20.REMOVE COOLER CONDENSER ASSEMBLY

a.
I112408C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guides to remove the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.