Home › Engine / Hybrid System › M20A-FXS (COOLING) › RADIATOR › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _084057 M20A-FXS COOLING _0404853 RADIATOR A

M20A-FXS COOLING  RADIATOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Front bumper assembly
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Simple intelligent parking assist system
Front television camera view adjustment Panoramic View Monitor System (Click here)

PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 5.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide G9040 6.REMOVE INVERTER WATER PUMP WITH MOTOR ASSEMBLY

Hide 7.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.
A396422

Remove the 4 bolts and front bumper upper reinforcement sub-assembly from the vehicle.


Hide 8.REMOVE NO. 1 RADIATOR GRILLE RETAINER

Hide 9.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53510 11.REMOVE HOOD LOCK ASSEMBLY

Hide 17751 12.REMOVE NO. 1 AIR CLEANER INLET

a.
A432798

Remove the 4 bolts and No. 1 air cleaner inlet from the upper radiator support sub-assembly and air cleaner case sub-assembly.


Hide 53205 13.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.
A394694C01
0.083,0.083 0.375,0.302 0.292,0.219 12 true *A 0.083,2.365 0.375,2.583 0.292,0.219 12 true *B
*A for LHD
*B for RHD


Disengage the clamp to disconnect the hood control cable sub-assembly from the upper radiator support sub-assembly.


b.
A393650

Disengage the 3 clamps to disconnect the wire harness from the horn and hood lock support assembly.


c.
A452447

Disengage the 7 clamps to disconnect the wire harness from the fan shroud and upper radiator support sub-assembly.


d.

Disconnect the wire harness connector from the cooling fan wire.


e.

Lift up the lever to disengage the lock, and disconnect the wire harness connector from the cooling fan motor.


f.
A433108

Disengage the 3 clamps to disconnect the wire harness from the fan shroud.


g.
A394676

Remove the 5 bolts and upper radiator support sub-assembly together with hood lock support sub-assembly from the vehicle.


Hide 16594 14.REMOVE NO. 2 RADIATOR AIR GUIDE

a.
A432803

Disengage the 2 claws and 3 guides to remove the No. 2 radiator air guide from the radiator assembly.


Hide 16261 15.DISCONNECT WATER BY-PASS HOSE

a.
A432804

Slide the clip and disconnect the water by-pass hose from the radiator assembly.


Hide 16264D 16.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A432805

Disengage the 3 clamps from the fan shroud.


b.

Slide the clip and disconnect the No. 2 water by-pass hose from the radiator assembly.


Hide 16571C 17.DISCONNECT NO. 1 RADIATOR HOSE

a.
A432811

Disengage the clamp.


b.

Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

a.
A432809

Disengage the clamp.


b.

Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.


Hide G922H 19.DISCONNECT HYBRID RADIATOR INLET HOSE

a.
A432808

Disengage the clamp.


b.

Slide the clip and disconnect the hybrid radiator inlet hose from the radiator assembly.


Hide G922AA 20.DISCONNECT NO. 1 INVERTER COOLING INLET HOSE

a.
A432810

Slide the clip and disconnect the No. 1 inverter cooling inlet hose from the radiator assembly.


Hide 21.SEPARATE NO. 1 INVERTER COOLING OUTLET HOSE

a.
A432806

Disengage the claw.


b.

Disengage the 2 clamps to separate the No. 1 inverter cooling outlet hose from the fan shroud.


Hide G922E 22.SEPARATE HYBRID WATER PUMP INLET HOSE

a.
A432807

Disengage the 3 clamps to separate the hybrid water pump inlet hose from the fan shroud.


Hide G922F 23.SEPARATE NO. 1 HYBRID WATER PUMP OUTLET HOSE

a.
A433109

Disengage the clamp to separate the No. 1 hybrid water pump outlet hose from the fan shroud.


Hide 52611 24.REMOVE FRONT BUMPER ENERGY ABSORBER

Hide 52131A 25.REMOVE FRONT BUMPER REINFORCEMENT

Hide 16595B 26.REMOVE NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 27.REMOVE NO. 1 RADIATOR AIR GUIDE RH

Hide 88703 28.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88707 29.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

Hide 88460 30.REMOVE COOLER CONDENSER ASSEMBLY

Hide 16400 31.REMOVE RADIATOR ASSEMBLY

a.

Remove the radiator assembly with the fan shroud assembly from the vehicle body.


b.
A432816

Disengage the 2 claws.


c.

Disengage the 2 guides to remove the fan shroud assembly from the radiator assembly.

NOTICE:

Do not damage the radiator assembly when removing the fan shroud assembly.



Hide 16523A 32.REMOVE RADIATOR SUPPORT CUSHION

a.
A432817

Remove the 2 radiator support cushions from the radiator assembly.


Hide 16533C 33.REMOVE LOWER RADIATOR SUPPORT

a.
A432818

Remove the 2 lower radiator supports from the radiator assembly.


Hide 34.REMOVE RADIATOR DRAIN COCK PLUG

a.
A432819

Remove the 2 radiator drain cock plugs.


b.

Remove the 2 O-rings from the 2 radiator drain cock plugs.