Home › Engine / Hybrid System › M20A-FXS (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083957 M20A-FXS INTAKE / EXHAUST _0404362 INTAKE MANIFOLD A

M20A-FXS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Cleaning the deposits from the throttle body with motor assembly

·

Air leak from intake system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 53141F 1.REMOVE RADIATOR COVER

Hide 17751 2.REMOVE NO. 1 AIR CLEANER INLET

Hide 22030 3.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25601 4.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 89421 5.REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 23827D 6.REMOVE NO. 1 FUEL VAPOR FEED HOSE

a.
A432876

Slide the hose clip and disconnect the No. 1 fuel vapor feed hose from the intake manifold.


b.

Disengage the clamp to disconnect the No. 1 fuel vapor feed hose.


Hide 7.DISCONNECT ENGINE WIRE

a.
A432877

Disconnect the fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


b.
A432878

Disconnect the 2 connectors.


c.

Remove the 3 bolts and disconnect the engine wire from the fuel delivery guard, intake manifold and timing chain cover assembly.


d.

Disengage the 3 clamps to disconnect the engine wire from the intake manifold and fuel vapor feed pipe.


e.
A432879

Remove the bolt and disconnect the engine wire from the intake manifold.


f.

Disengage the clamp to disconnect the engine wire from the intake manifold.


Hide 16279 8.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A432880

Slide the clip and disconnect the water by-pass hose from the No. 3 water by-pass pipe.


b.

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


Hide 16264D 9.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A432881

Disengage the clamp to disconnect the No. 2 water by-pass hose from the No. 2 water hose clamp bracket.


Hide 10.REMOVE BRACKET

a.
A432882C01
0.708,1.177 1.021,1.469 true 2.677,0.781 2.99,1.073 true 3.052,1.021 3.271,1.198 0.219,0.177 10 true *1 0.438,1.042 0.646,1.229 0.208,0.188 10 true *2
*1 Wire Harness Clamp Bracket
*2 No. 2 Water Hose Clamp Bracket


Using an 8 mm socket wrench, remove the bolt and wire harness clamp bracket from the intake manifold.


b.

Remove the bolt and No. 2 water hose clamp bracket from the intake manifold.


Hide 17138B 11.REMOVE INTAKE MANIFOLD STAY

a.
A432883

Disengage the clamp to disconnect the HV air conditioning wire from the No. 1 water hose clamp bracket.


b.
A432884N01
1.573,1.542 1.729,1.74 0.156,0.198 10 true A 2.573,0.76 2.729,0.958 0.156,0.198 10 true B

Using an 8 mm socket wrench, remove the bolt (A).


c.

Remove the bolt (B).


d.

Disengage the guide to remove the intake manifold stay.


Hide 17111 12.REMOVE INTAKE MANIFOLD

a.
A432885

Remove the 4 bolts, 2 nuts, No. 2 fuel delivery guard and intake manifold from the cylinder head sub-assembly.


Hide 17177 13.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A432886

Remove the No. 1 intake manifold to head gasket from the intake manifold.


Hide 14.REMOVE VACUUM HOSE

a.
A432887

Remove the vacuum hose from the intake manifold.