Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › BATTERY VOLTAGE SENSOR (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404377 BATTERY VOLTAGE SENSOR(for NICKEL METAL HYDRIDE BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR(for NICKEL METAL HYDRIDE BATTERY)  INSTALLATION  


PROCEDURE

Hide 89892A 1.INSTALL BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375905C02
1.385,1.26 2.01,2.188 2.01,2.188 2.271,2.188 true 0.906,2.781 1.615,2.781 true 2.323,2.104 2.635,2.302 0.313,0.198 10 false *a 1.677,2.698 1.99,2.896 0.313,0.198 10 false *b
*a Black Label
*b Pin


Install the battery voltage sensor to the HV battery with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

Check color of the label.

·

If the battery voltage sensor has been struck or dropped, replace it.

·

Make sure to align the hole of the battery voltage sensor with the pin.




b.

Connect the battery voltage sensor connector.

NOTICE:

Make sure that the connector is connected securely.



Hide G92Q1 2.INSTALL NO. 1 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Pull back the No. 2 hybrid battery shield sub-assembly to install the No. 1 HV battery shield panel to the HV battery.

HINT:

Pull back the No. 2 hybrid battery shield sub-assembly until there is sufficient clearance for the 2 stud bolts of the No. 1 HV battery shield panel.



b.

Install the bolt and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the battery voltage sensor connector.


d.

Engage the clamp.


Hide G920L 3.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 6 bolts and 5 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Move the HV battery to the installation position.


c.
A378149C02
1.688,0.083 1.948,0.281 0.26,0.198 10 true *b 2.198,0.333 2.458,0.531 0.26,0.198 10 true *a 3,0.667 3.26,0.865 0.26,0.198 10 true *a 2.948,1.938 3.208,2.135 0.26,0.198 10 true *a 0.073,0.438 0.333,0.635 0.26,0.198 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the 4 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide G9230 9.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 76974F 12.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 13.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 14.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 15.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 16.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 17.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY