Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404378 HV BATTERY(for NICKEL METAL HYDRIDE BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY(for NICKEL METAL HYDRIDE BATTERY)  INSTALLATION  


PROCEDURE

Hide G920L 7.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A376709C03
1.385,0.094 1.698,0.292 0.313,0.198 10 false *a 1.906,0.083 2.219,0.281 0.313,0.198 10 false *a 2.313,0.24 2.625,0.438 0.313,0.198 10 false *a 2.75,0.427 3.063,0.625 0.313,0.198 10 false *a 3.083,0.646 3.396,0.844 0.313,0.198 10 false *a 0.094,0.302 0.406,0.5 0.313,0.198 10 false *a 0.135,1.083 0.448,1.281 0.313,0.198 10 false *b 0.469,1.323 0.781,1.521 0.313,0.198 10 false *b 0.906,1.573 1.219,1.771 0.313,0.198 10 false *b 1.333,1.854 1.646,2.052 0.313,0.198 10 false *b 2.167,1.625 2.396,1.813 0.229,0.188 10 true *b
*a Bolt
*b Nut


Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 6 bolts and 5 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 8.INSTALL HV BATTERY

CAUTION:

Wear insulated gloves.


a.
A378149C02
1.688,0.083 1.948,0.281 0.26,0.198 10 true *b 2.198,0.333 2.458,0.531 0.26,0.198 10 true *a 3,0.667 3.26,0.865 0.26,0.198 10 true *a 2.948,1.938 3.208,2.135 0.26,0.198 10 true *a 0.073,0.438 0.333,0.635 0.26,0.198 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the HV battery to the vehicle with the 4 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 9.CONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the battery voltage sensor connector.


b.

Engage the clamp.


Hide G92F1 10.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT

a.

Engage the claw to install the No. 1 hybrid battery exhaust duct to the HV battery.


b.

Install the clip.


Hide 82161 11.CONNECT FLOOR WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 12.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 13.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Wear insulated gloves.


a.
A375874C02
1.354,1.177 1.594,1.177 false 1.219,0.948 1.354,0.677 1.354,0.677 1.521,0.677 true 1.573,0.604 1.802,0.792 0.229,0.188 10 false *a 1.094,0.125 1.323,0.313 0.229,0.188 10 false *b 1.646,1.094 1.875,1.281 0.229,0.188 10 false *1
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 14.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 71033 15.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.

Install the rear seat cushion leg sub-assembly with the 6 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 76971G 16.INSTALL REAR UNDER COVER

a.

Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.


b.

Engage the 2 clips.


Hide 76974F 17.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 18.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 19.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 20.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 21.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 22.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY