Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM J

M20A-FXS ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A425736E07
1.021,0.563 1.208,0.74 0.188,0.177 10 false 10 1.052,1.073 1.177,1.24 0.125,0.167 10 false 8 1.906,0.573 2.031,0.74 0.125,0.167 10 false 9 1.906,1.073 2.031,1.24 0.125,0.167 10 false 7 1.188,1.51 1.865,1.698 0.677,0.188 10 false IG2 NO. 1 0.813,1.792 1.021,1.958 0.208,0.167 10 false 1A 0.823,1.969 2.271,2.177 1.448,0.208 10 false No. 1 Integration Relay 0.365,2.323 1.021,2.521 0.656,0.198 10 false IG2-MAIN 0.688,3.115 2.792,3.5 2.104,0.385 10 false from Certification ECU (Smart Key ECU Assembly) 0.375,4.021 1.479,4.271 1.104,0.25 10 false MAIN 0.542,4.99 1.677,5.26 1.135,0.271 10 false Auxiliary Battery 2.438,0.854 2.688,1.042 0.25,0.188 10 false INJ 3.76,0.573 3.885,0.74 0.125,0.167 10 false 1 3.76,0.885 3.885,1.052 0.125,0.167 10 false 3 4.896,0.573 5.021,0.74 0.125,0.167 10 false 2 3.948,0.677 4.198,0.865 0.25,0.188 10 false +B 3.958,1.01 4.292,1.198 0.333,0.188 10 false GND 4.469,0.688 4.802,0.865 0.333,0.177 10 false IGT1 3.281,1.354 3.615,1.542 0.333,0.188 10 false C74 3.281,1.531 5.656,1.76 2.375,0.229 10 false Ignition Coil Assembly (No. 1 Cylinder) 3.76,2.167 3.885,2.333 0.125,0.167 10 false 1 3.75,2.49 3.875,2.656 0.125,0.167 10 false 3 4.885,2.177 5.01,2.344 0.125,0.167 10 false 2 3.948,2.302 4.198,2.49 0.25,0.188 10 false +B 3.948,2.625 4.281,2.813 0.333,0.188 10 false GND 4.479,2.302 4.813,2.479 0.333,0.177 10 false IGT2 3.313,3.021 3.646,3.208 0.333,0.188 10 false C75 3.302,3.198 5.677,3.427 2.375,0.229 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.75,3.781 3.875,3.948 0.125,0.167 10 false 1 3.75,4.083 3.875,4.25 0.125,0.167 10 false 3 4.896,3.781 5.021,3.948 0.125,0.167 10 false 2 3.958,3.875 4.208,4.063 0.25,0.188 10 false +B 3.958,4.208 4.292,4.396 0.333,0.188 10 false GND 4.479,3.875 4.813,4.052 0.333,0.177 10 false IGT3 3.354,4.594 3.688,4.781 0.333,0.188 10 false C76 3.333,4.771 5.708,5 2.375,0.229 10 false Ignition Coil Assembly (No. 3 Cylinder) 3.75,5.281 3.875,5.448 0.125,0.167 10 false 1 3.76,5.698 3.885,5.865 0.125,0.167 10 false 3 4.885,5.292 5.01,5.458 0.125,0.167 10 false 2 3.958,5.385 4.208,5.573 0.25,0.188 10 false +B 3.958,5.823 4.292,6.01 0.333,0.188 10 false GND 4.479,5.417 4.813,5.594 0.333,0.177 10 false IGT4 3.344,6.198 3.677,6.385 0.333,0.188 10 false C77 3.344,6.354 5.719,6.583 2.375,0.229 10 false Ignition Coil Assembly (No. 4 Cylinder) 6.26,6.198 6.594,6.385 0.333,0.188 10 false C97 6.25,6.365 6.604,6.552 0.354,0.188 10 false ECM 5.531,0.573 5.708,0.75 0.177,0.177 10 false 49 5.781,0.573 6.115,0.75 0.333,0.177 10 false IGT1 5.76,2.188 6.094,2.365 0.333,0.177 10 false IGT2 5.76,3.781 6.094,3.958 0.333,0.177 10 false IGT3 5.781,5.281 6.115,5.458 0.333,0.177 10 false IGT4 5.51,2.167 5.688,2.344 0.177,0.177 10 false 48 5.521,3.771 5.698,3.948 0.177,0.177 10 false 47 5.5,5.281 5.677,5.458 0.177,0.177 10 false 46 6.833,0.167 7.104,0.365 0.271,0.198 10 false 5 V 6.833,1.781 7.104,1.969 0.271,0.188 10 false 5 V 6.844,3.375 7.135,3.563 0.292,0.188 10 false 5 V 6.854,4.906 7.125,5.083 0.271,0.177 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test first. If none of the cylinders spark, or if only some cylinders do not spark, check this circuit to determine if the ignition coil and spark plug are normal.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A402447C29
0.281,0.469 0.688,0.688 0.406,0.219 0.281,0.813 0.688,1.031 0.406,0.219 0.281,1.146 0.688,1.365 0.406,0.219 0.281,1.479 0.688,1.698 0.406,0.219 0.948,1.719 1.365,1.302 false 2.521,1.708 2.104,1.302 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.74,1.667 1.052,1.865 0.313,0.198 10 false +B 2.583,1.667 2.896,1.865 0.313,0.198 10 false GND 0.365,0.51 0.677,0.708 0.313,0.198 10 false C74 0.365,0.844 0.677,1.042 0.313,0.198 10 false C75 0.365,1.188 0.677,1.385 0.313,0.198 10 false C76 0.365,1.51 0.677,1.708 0.313,0.198 10 false C77
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C74-1 (+B) - C74-3 (GND) Power switch on (IG) 11 to 14 V
C75-1 (+B) - C75-3 (GND) Power switch on (IG) 11 to 14 V
C76-1 (+B) - C76-3 (GND) Power switch on (IG) 11 to 14 V
C77-1 (+B) - C77-3 (GND) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the C97 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C74-2 (IGT1) - C97-49 (IGT1) Always Below 1 Ω
C75-2 (IGT2) - C97-48 (IGT2) Always Below 1 Ω
C76-2 (IGT3) - C97-47 (IGT3) Always Below 1 Ω
C77-2 (IGT4) - C97-46 (IGT4) Always Below 1 Ω
C74-2 (IGT1) or C97-49 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C75-2 (IGT2) or C97-48 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C76-2 (IGT3) or C97-47 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C77-2 (IGT4) or C97-46 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C74-3 (GND) - Body ground Always Below 1 Ω
C75-3 (GND) - Body ground Always Below 1 Ω
C76-3 (GND) - Body ground Always Below 1 Ω
C77-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
a.

Disconnect the 1A No. 1 integration relay connector.


b.

Disconnect the C74, C75, C76 and C77 ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-9 - C74-1 (+B) Always Below 1 Ω
1A-9 - C75-1 (+B) Always Below 1 Ω
1A-9 - C76-1 (+B) Always Below 1 Ω
1A-9 - C77-1 (+B) Always Below 1 Ω
1A-9 or C74-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1A-9 or C75-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1A-9 or C76-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1A-9 or C77-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)
a.

Inspect the No. 1 integration relay (IG2 NO. 1 relay).

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG