Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The hybrid vehicle control ECU compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the power switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IG2 signal of the hybrid vehicle control ECU and the IG control status signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU

·

ECM

·

NO. 1 integration relay

·

Wire harness or connector


Does not come on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and wait for 15 seconds or more.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394812E01
0.063,0.833 0.917,1.344 0.854,0.51 10 false from Auxiliary Battery 1.448,0.698 1.594,0.927 0.146,0.229 10 false 1 1.719,0.688 1.865,0.917 0.146,0.229 10 false 2 1.344,0.969 1.99,1.177 0.646,0.208 10 false IG2-MAIN 2.26,0.74 2.469,0.938 0.208,0.198 10 false 10 2.323,1.146 2.563,1.344 0.24,0.198 10 false 8 2.302,1.938 2.542,2.135 0.24,0.198 10 false 1A 2.719,1.552 3.365,1.76 0.646,0.208 10 false IG2 NO. 1 3.656,0.729 3.865,0.927 0.208,0.198 10 false 9 3.667,1.146 3.906,1.344 0.24,0.198 10 false 7 2.313,2.083 3.771,2.323 1.458,0.24 10 false NO. 1 Integration Relay 4.417,0.688 4.563,0.917 0.146,0.229 10 false 1 4.708,0.677 4.854,0.906 0.146,0.229 10 false 2 4.146,0.969 5.146,1.188 1,0.219 10 false ECU-IG2 NO. 1 5.583,0.625 5.792,0.823 0.208,0.198 10 false 3 5.51,0.823 5.802,1.021 0.292,0.198 10 false A49 5.583,1.063 5.792,1.26 0.208,0.198 10 false 5 5.552,1.26 5.792,1.458 0.24,0.198 10 false F2 5.615,1.969 5.823,2.167 0.208,0.198 10 false 6 5.51,2.167 5.823,2.365 0.313,0.198 10 false A38 5.563,2.365 5.802,2.563 0.24,0.198 10 false 59 5.51,2.552 5.813,2.75 0.302,0.198 10 false C63 5.615,3.531 5.854,3.729 0.24,0.198 10 false 17 5.875,0.729 6.167,0.927 0.292,0.198 10 false IG2 5.875,1.26 6.188,1.458 0.313,0.198 10 false E01 5.417,1.635 7.135,1.844 1.719,0.208 10 false Hybrid Vehicle Control ECU 5.875,2.156 6.333,2.354 0.458,0.198 10 false IGSW 5.875,2.542 6.333,2.74 0.458,0.198 10 false E1 6.167,2.885 6.625,3.083 0.458,0.198 10 false ECM 5.875,3.625 6.333,3.823 0.458,0.198 10 false IG1D 5.344,4.094 7.146,4.479 1.802,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.354,3.938 5.573,4.135 0.219,0.198 10 false F1

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 11.0 V or higher


Result:
Proceed to
OK
NG




OK

2.CLEAR DTC

NG

9.CHARGE OR REPLACE AUXILIARY BATTERY
2.CLEAR DTC
a.

Turn the power switch on (IG) and wait for 15 seconds or more.


b.

Turn the power switch off and wait for 2 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

g.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output. A
P253012 is not output. B



e.

Turn the power switch off.



A

4.CHECK DTC OUTPUT (HYBRID CONTROL)

B

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U011087, U012987, U014087, U015187, U016487 or U117087 is also output. A
U011087, U012987, U014087, U015187, U016487 or U117087 is not output. B



e.

Turn the power switch off.



A

5.CHECK HYBRID VEHICLE CONTROL ECU

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HYBRID VEHICLE CONTROL ECU
a.
A389519C01
0.625,0.667 1.125,0.917 0.5,0.25 1.896,0.698 2.396,0.948 0.5,0.25 0.885,2.375 1.167,2.917 true 1.917,2.375 2.417,2.917 true 0.188,0.417 0.5,0.573 0.313,0.156 10 false *a 1.125,2.958 1.521,3.125 0.396,0.167 10 false IG2 2.365,2.948 2.76,3.115 0.396,0.167 10 false E01 0.76,0.688 1.063,0.885 0.302,0.198 10 false A49 2.073,0.719 2.271,0.917 0.198,0.198 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the hybrid vehicle control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (IG2) - F2-5 (E01) Power switch off 9 V or higher



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM

NG

6.CHECK ECM
a.
A389519C01
0.625,0.667 1.125,0.917 0.5,0.25 1.896,0.698 2.396,0.948 0.5,0.25 0.885,2.375 1.167,2.917 true 1.917,2.375 2.417,2.917 true 0.188,0.417 0.5,0.573 0.313,0.156 10 false *a 1.125,2.958 1.521,3.125 0.396,0.167 10 false IG2 2.365,2.948 2.76,3.115 0.396,0.167 10 false E01 0.76,0.688 1.063,0.885 0.302,0.198 10 false A49 2.073,0.719 2.271,0.917 0.198,0.198 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the A38 and C63 ECM connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (IG2) - F2-5 (E01) Power switch off 9 V or higher



d.

Reconnect the A38 and C63 ECM connectors.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

NG

7.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Remove the NO. 1 integration relay from the No. 1 engine room relay block.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


c.
A389501C02
0.656,0.667 1.156,0.917 0.5,0.25 1.25,2.75 0.875,2.375 true 0.188,0.573 0.5,0.729 0.313,0.156 10 false *a 1.208,2.781 1.688,2.938 0.479,0.156 10 false IG2 0.771,0.688 1.083,0.885 0.313,0.198 10 false A49
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (IG2) - Body ground Power switch off 1 V or less



d.

Install the NO. 1 integration relay.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC