Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P274A11  Transmission Fluid Temperature Sensor "C" Circuit Short to Ground  P274A15  Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the transmission fluid temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU internal malfunction
·

Hybrid vehicle control ECU malfunction


Transmission fluid temperature sensor malfunction
·

Internal transmission fluid temperature sensor malfunction

·

Open or short in transmission fluid temperature sensor


Wire harness between the transmission fluid temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness



DESCRIPTION

The resistance of the thermistor built into the transmission fluid temperature sensor changes in accordance with changes in the transmission fluid temperature. The lower the transmission fluid temperature, the higher the thermistor resistance. Conversely, the higher the transmission fluid temperature, the lower the resistance.

A380229E03
0.104,0.406 1.208,0.76 1.104,0.354 10 false Resistance (kΩ) 1.75,3.052 3.385,3.375 1.635,0.323 10 false Temperature (°C (°F)) 0.729,2.26 0.885,2.458 0.156,0.198 10 false 0 0.865,2.396 1.021,2.594 0.156,0.198 10 false 0 1.563,2.396 1.865,2.625 0.302,0.229 10 false 50 1.188,2.396 1.49,2.625 0.302,0.229 10 false 25 1.938,2.396 2.24,2.625 0.302,0.229 10 false 75 2.271,2.396 2.573,2.625 0.302,0.229 10 false 100 2.635,2.396 2.938,2.625 0.302,0.229 10 false 125 3.01,2.396 3.313,2.625 0.302,0.229 10 false 150 0.719,2.031 1.021,2.26 0.302,0.229 10 false 5 0.688,1.781 0.99,2.01 0.302,0.229 10 false 10 0.677,1.563 0.979,1.792 0.302,0.229 10 false 15 0.688,1.333 0.99,1.563 0.302,0.229 10 false 20 0.688,1.115 0.99,1.344 0.302,0.229 10 false 25 0.688,0.885 0.99,1.115 0.302,0.229 10 false 30 1.167,2.635 1.479,2.906 0.313,0.271 10 false (77) 0.813,2.625 1.125,2.896 0.313,0.271 10 false (32) 1.5,2.646 1.875,2.927 0.375,0.281 10 false (122) 1.885,2.656 2.292,2.927 0.406,0.271 10 false (167) 2.26,2.656 2.667,2.927 0.406,0.271 10 false (212) 2.635,2.656 3.031,2.938 0.396,0.281 10 false (257) 3.021,2.656 3.417,2.99 0.396,0.333 10 false (302)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground Line short or short to ground in the transmission fluid temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Transmission fluid temperature sensor)


Does not come on Master Warning:
Comes on
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open Open or short to +B in the transmission fluid temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Transmission fluid temperature sensor)


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P274A11 Transaxle Oil Temperature
P274A15

HINT:

After confirming that DTC P274A11 or P274A15 is output, use the GTS to check "Transaxle Oil Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A385273E70
4.969,2.844 6.979,3.396 2.01,0.552 10 false Hybrid Vehicle Control ECU 0.531,2.823 2.542,3.375 2.01,0.552 10 false Transmission Fluid Temperature Sensor (Hybrid Vehicle Transaxle Assembly) 0.531,2.667 0.844,2.865 0.313,0.198 10 false C1 4.958,2.677 5.271,2.875 0.313,0.198 10 false A49 5.938,1.281 6.427,1.625 0.49,0.344 10 false ADC 4.865,1.917 5.417,2.219 0.552,0.302 10 false ETTA 4.854,1.167 5.333,1.458 0.479,0.292 10 false TTA 1.885,1.167 2.365,1.458 0.479,0.292 10 false TTA 1.802,1.906 2.354,2.208 0.552,0.302 10 false ETTA 4.604,1.167 4.948,1.49 0.344,0.323 10 false 21 4.604,1.917 4.948,2.24 0.344,0.323 10 false 31 2.313,1.146 2.656,1.469 0.344,0.323 10 false 3 2.302,1.917 2.646,2.24 0.344,0.323 10 false 13 3.688,1.167 4.031,1.49 0.344,0.323 10 false 10 3.01,1.167 3.354,1.49 0.344,0.323 10 false 10 3.688,1.917 4.031,2.24 0.344,0.323 10 false 11 3.031,1.938 3.375,2.26 0.344,0.323 10 false 11 2.625,2.677 4.74,3.229 2.115,0.552 10 false No. 1 Engine Room Relay Block 2.625,2.5 2.938,2.698 0.313,0.198 10 false CA4

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)
a.

Check that the intermediate connector which connects the transmission fluid temperature sensor to the hybrid vehicle control ECU is securely connected with no deformation, and that there is no contamination by water or foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)
a.
A376649

Check the connection condition of the transmission fluid temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (TRANSAXLE OIL TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (TRANSAXLE OIL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Transaxle Oil Temperature.


d.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Transaxle Oil Temperature
50003 397 322
Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
a.
A376649

Disconnect the transmission fluid temperature sensor connector.


b.
A385117C04
0.25,0.917 0.75,1.167 0.5,0.25 2.458,0.542 1.823,1 true 1.625,1.438 0.896,1.823 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.469,0.396 2.927,0.594 0.458,0.198 10 false TTA 0.604,1.844 1.063,2.042 0.458,0.198 10 false ETTA 0.427,0.938 0.74,1.135 0.313,0.198 10 false C1
*a Component without harness connected
(Transmission Fluid Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-3 (TTA) - C1-13 (ETTA) Power switch off 1.393 to 75.8 kΩ



c.

Reconnect the transmission fluid temperature sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

6.CHECK HYBRID VEHICLE CONTROL ECU
a.
A389500C11
0.583,0.958 1.083,1.208 0.5,0.25 0.75,2.583 0.865,1.917 true 1.333,2.583 0.875,1.844 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.563,2.615 1.125,2.781 0.563,0.167 10 false ETTA 1.281,2.615 1.844,2.781 0.563,0.167 10 false TTA 0.708,0.979 1.031,1.156 0.323,0.177 10 false A49
*a Component with harness connected
(to Hybrid Vehicle Control ECU)


Connect terminals 21 (TTA) and 31 (ETTA) of the A49 hybrid vehicle control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Transaxle Oil Temperature.


e.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Transaxle Oil Temperature
50003 397 322
OK:
Tester Display Condition Specified Condition
Transaxle Oil Temperature Terminals A49-21 (TTA) and A49-31 (ETTA) connected
Power switch on (IG)
215°C (419°F)



Result:
Proceed to
OK
NG


f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
a.
A376649

Disconnect the transmission fluid temperature sensor connector.


b.
A385117C04
0.25,0.917 0.75,1.167 0.5,0.25 2.458,0.542 1.823,1 true 1.625,1.438 0.896,1.823 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.469,0.396 2.927,0.594 0.458,0.198 10 false TTA 0.604,1.844 1.063,2.042 0.458,0.198 10 false ETTA 0.427,0.938 0.74,1.135 0.313,0.198 10 false C1
*a Component without harness connected
(Transmission Fluid Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-3 (TTA) - C1-13 (ETTA) Power switch off 1.393 to 75.8 kΩ



c.

Reconnect the transmission fluid temperature sensor connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the transmission fluid temperature sensor connector.


b.

Disconnect the hybrid vehicle control ECU connector.


c.
A496620C01
1.458,0.417 1.958,0.667 0.5,0.25 1.458,2.5 1.958,2.75 0.5,0.25 2.344,0.698 1.667,1.156 true 2.323,2.021 1.792,1.469 true 1.917,4.333 1.521,3.969 true 1,4.333 1.51,3.833 true 0.25,0.25 0.5,0.5 0.25,0.25 10 false *a 0.333,2.417 0.563,2.656 0.229,0.24 10 false *b 2.375,0.531 2.771,0.771 0.396,0.24 10 false TTA 2.375,2.042 2.854,2.281 0.479,0.24 10 false ETTA 0.75,4.344 1.083,4.583 0.333,0.24 10 false TTA 1.917,4.333 2.333,4.583 0.417,0.25 10 false ETTA 1.604,2.552 2.063,2.75 0.458,0.198 10 false A49 1.625,0.458 2.052,0.677 0.427,0.219 10 false C1
*a Front view of wire harness connector
(to Transmission Fluid Temperature Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-3 (TTA) - A49-21 (TTA) Power switch off Below 1 Ω
C1-13 (ETTA) - A49-31 (ETTA) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C1-3 (TTA) or A49-21 (TTA) - Body ground and other terminals Power switch off 10 kΩ or higher
C1-13 (ETTA) or A49-31 (ETTA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Reconnect the transmission fluid temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR