Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P314A31  Motor Electronics Coolant Pump "A" No Signal  


DESCRIPTION

Refer to the description for DTC P0C7396.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P0C7396

The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P314A31 Motor Electronics Coolant Pump "A" No Signal The inverter water pump speed signal is not sent to the hybrid vehicle control ECU when the power switch is turned on (READY).*
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter water pump assembly

·

INV W/PMP fuse

·

IGCT relay

·

IGCT-IG fuse


Comes on Master Warning: Comes on

*: Either of the following conditions is met.
·

A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control ECU is detected.

·

A malfunction in the inverter water pump assembly power source circuit is detected.

·

A malfunction in the +B line is detected.

·

A malfunction in hybrid vehicle control ECU power source circuit is detected.


Related Data List
DTC No. Data List
P314A31
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Ready Signal



Related Active Test
DTC No. Active Test
P314A31 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.

·

When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

d.

Perform the "Activate the Inverter Water Pump" Active Test.


e.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).


HINT:

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the inverter water pump assembly connector.


c.
A389515C02
0.615,0.313 1.115,0.563 0.5,0.25 0.458,3.333 0.958,3.583 0.5,0.25 1.333,4 1.573,3.552 true 1.083,2.583 0.729,2.115 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.26,2.938 0.573,3.094 0.313,0.156 10 false *b 0.979,2.625 1.563,2.833 0.583,0.208 10 false NIWP 1.177,4.073 1.594,4.229 0.417,0.156 10 false NWP 0.74,0.344 1.073,0.552 0.333,0.208 10 false A49 0.635,3.365 0.969,3.573 0.333,0.208 10 false A6
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A49-14 (NIWP) - A6-2 (NWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A49-14 (NIWP) or A6-2 (NWP) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the inverter water pump assembly connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the A6 inverter water pump assembly connector.


b.

Turn the power switch on (IG).


c.
A389500C14
0.573,0.958 1.073,1.208 0.5,0.25 1.813,1 2.313,1.25 0.5,0.25 0.5,2.417 0.74,1.781 true 1.667,2.417 1.823,1.719 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.333,2.479 0.833,2.635 0.5,0.156 10 false NIWP 1.573,2.479 2.135,2.646 0.563,0.167 10 false E1 0.698,0.99 1.021,1.208 0.323,0.219 10 false A49 1.979,1.031 2.302,1.25 0.323,0.219 10 false F2
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-14 (NIWP) - F2-6 (E1) Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the A6 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

d.

Perform the "Activate the Inverter Water Pump" Active Test.


e.
A389525C01
0.552,0.125 1.052,0.375 0.5,0.25 1.802,0.167 2.302,0.417 0.5,0.25 1.667,1.5 1.813,0.875 true 0.417,1.5 0.719,0.938 true 0.219,0.063 0.531,0.219 0.313,0.156 10 false *a 0.24,1.542 0.719,1.708 0.479,0.167 10 false NIWP 1.563,1.531 2.042,1.698 0.479,0.167 10 false E1 3.073,2.677 3.417,2.854 0.344,0.177 10 false GND 0.677,0.156 1.01,0.354 0.333,0.198 10 false A49 1.969,0.198 2.302,0.396 0.333,0.198 10 false F2
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal A49-14 (NIWP) - F2-6 (E1)
Equipment Setting 5 V/DIV., 5 ms./DIV.
Condition Power switch on (IG), during Active Test

OK:

The period of the wavelength is 13 msec or less.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

12.REPLACE INVERTER WATER PUMP ASSEMBLY
9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)

NG

14.CHECK FUSE (INV W/PMP)
10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)
a.

Remove the IGCT relay from the No. 1 engine room relay block.


b.

Disconnect the inverter water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A389526C01
0.521,1.333 1.021,1.583 0.5,0.25 1.969,1.531 2.417,1.917 true 4.177,0.073 4.49,0.229 0.313,0.156 10 false *1 2.313,1.969 2.896,2.125 0.583,0.156 10 false +BWP 0.365,0.229 0.677,0.385 0.313,0.156 10 false *a 6.021,1.167 6.333,1.323 0.313,0.156 10 false *b 0.688,1.354 1,1.51 0.313,0.156 10 false A6
*1 No. 1 Engine Room Relay Block - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
*b IGCT Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A6-4 (+BWP) - 5 (IGCT relay) Power switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


HINT:
A288054C07
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 1 Engine Room Relay Block

Apply slight vibration with a finger to the No. 1 engine room relay block and check whether a malfunction occurs.

·

INV W/PMP fuse

Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.

·

IGCT relay

Apply slight vibration with a finger to the IGCT relay and check whether a malfunction occurs.




d.

Reconnect the inverter water pump assembly connector.


e.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

15.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the inverter water pump assembly connector.


b.
A425328C02
1.5,0.833 1.917,1.083 0.417,0.25 1.083,2.333 1.333,1.823 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.948,2.385 1.406,2.583 0.458,0.198 10 false GND 1.635,0.885 2.094,1.083 0.458,0.198 10 false A6
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Reconnect the inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

13.ADD HV COOLANT AND PERFORM AIR BLEEDING
13.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END

14.CHECK FUSE (INV W/PMP)
a.
A389516C01
2.667,2.156 1.75,1.635 true 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1 2.729,2.188 3.042,2.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

18.CONNECT SECURELY
15.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
a.

Check installation condition of the INV W/PMP fuse.

OK:

INV W/PMP fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

NG

19.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
16.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)
a.

Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Remove the IGCT relay from the No. 1 engine room relay block.


c.

Disconnect the inverter water pump assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

A389527C01
0.531,1.365 1.031,1.615 0.5,0.25 1.948,1.573 2.333,1.927 true 3.792,0.031 4.104,0.188 0.313,0.156 10 false *1 0.385,0.302 0.698,0.458 0.313,0.156 10 false *a 3.927,0.74 4.24,0.896 0.313,0.156 10 false *b 6.021,1.167 6.333,1.323 0.313,0.156 10 false *c 2.229,1.958 2.729,2.115 0.5,0.156 10 false +BWP 0.698,1.385 0.948,1.583 0.25,0.198 10 false A6
*1 No. 1 Engine Room Relay Block - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
*b INV W/PMP Fuse Holder
*c IGCT Relay Holder - -


Standard Resistance:
Tester Connection Condition Specified Condition
2 (INV W/PMP fuse holder) - A6-4 (+BWP) Power switch off Below 1 Ω
1 (INV W/PMP fuse holder) - 5 (IGCT relay) Power switch off Below 1 Ω
2 (INV W/PMP fuse holder) or A6-4 (+BWP) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



e.

Reconnect the inverter water pump assembly connector.


f.

Install the IGCT relay.


g.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

17.CHECK FUSE (INV W/PMP)

NG

21.CHECK FUSE (INV W/PMP)
17.CHECK FUSE (INV W/PMP)
a.
A389516C01
2.667,2.156 1.75,1.635 true 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1 2.729,2.188 3.042,2.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)

NG

22.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
18.CONNECT SECURELY
a.

Connect the inverter water pump assembly connector securely.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

19.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
a.

Check the terminals of the INV W/PMP fuse holder.

OK:

The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

20.CHECK FUSE (INV W/PMP)

NG

26.CHECK FUSE (INV W/PMP)
20.CHECK FUSE (INV W/PMP)
a.
A389516C01
2.667,2.156 1.75,1.635 true 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1 2.729,2.188 3.042,2.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INV W/PMP FUSE)

NG

REPLACE FUSE (INV W/PMP)

21.CHECK FUSE (INV W/PMP)
a.
A389516C01
2.667,2.156 1.75,1.635 true 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1 2.729,2.188 3.042,2.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
22.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the inverter water pump assembly connector.


b.
A425328C03
1.5,0.833 1.917,1.083 0.417,0.25 1.083,2.333 1.333,1.823 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.948,2.385 1.406,2.583 0.458,0.198 10 false GND 1.635,0.885 2.094,1.083 0.458,0.198 10 false A6
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Reconnect the inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

23.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.CHECK FUSE HOLDER TERMINAL (INV W/PMP FUSE)
a.

Check the terminals of the INV W/PMP fuse holder.

OK:

The terminals of the INV W/PMP fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

24.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
24.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

25.ADD HV COOLANT AND PERFORM AIR BLEEDING
25.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

26.CHECK FUSE (INV W/PMP)
a.
A389516C01
2.667,2.156 1.75,1.635 true 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1 2.729,2.188 3.042,2.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)

NG

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
27.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP fuse holder.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)