Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM J

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Start Control  


DESCRIPTION

The drive start control is controlled by the hybrid vehicle control ECU.

If the hybrid vehicle control ECU determines that the shift lever and accelerator pedal are operated abnormally, hybrid system output is restricted and, when necessary, a warning is displayed on the combination meter assembly.

C312753E59
0.344,0.25 2.656,0.469 2.313,0.219 10 false Accelerator Pedal Sensor Assembly 0.365,1.052 1.563,1.292 1.198,0.24 10 false Yaw Rate Sensor 0.406,2.198 2.573,2.833 2.167,0.635 10 false Shift Lever Position Sensor 0.396,3.406 1.979,3.813 1.583,0.406 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.917,3.771 4.031,4.125 1.115,0.354 10 false Vehicle Speed 2.771,2.604 4.594,2.938 1.823,0.333 10 false Shift Lever Position 2.677,1.458 3.979,1.656 1.302,0.198 10 false Vehicle Acceleration 2.76,0.479 3.938,0.854 1.177,0.375 10 false Actual accelerator opening 5.427,1.073 7.052,1.667 1.625,0.594 10 false Meter Display Request 5.5,3.115 6.99,3.51 1.49,0.396 10 false Hybrid System Output Request 3.708,4.198 6.083,4.625 2.375,0.427 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

HINT:

Even if the accelerator pedal position is maintained, the hybrid system output may increase when driving uphill and decrease when driving downhill. This is due to drive start control controlling the hybrid system output, and is not a malfunction.


PROCEDURE

1.SYMPTOM CONFIRMATION
a.

Interview the customer to confirm the problem.


Result:
Result Proceed to
Hunting A
Hesitation/poor acceleration B



A

2.PAST ACTIVATION CONFIRMATION

B

7.PAST ACTIVATION CONFIRMATION
2.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from P to (D or S) or R.



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from R to (D or S), from (D or S) or N to R.

A396026E54
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 0.771,3.271 2.25,3.656 1.479,0.385 10 false Hybrid System Output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.438,4.125 7.094,4.74 2.656,0.615 10 false *: The hybrid system output restricted level differs between pattern A and pattern B.



·

Items Controlled

-

Hybrid system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is in P or N.



Reverse control

Activation conditions


·

The shift lever is in R.

·

The accelerator pedal is depressed excessively.

A396028E54
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 0.948,3.167 2.375,3.646 1.427,0.479 10 false Hybrid System Output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

Hybrid system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is moved to any position other than R.




HINT:
·

The hybrid system output restricted level differs between Pattern A, Pattern B and Reverse control.

·

During Shift control or Reverse control, hybrid system output is adjusted based on the road gradient.




Result:
Result Proceed to
Performed A
Not performed B



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


f.

Turn the power switch off.


Result:
Result Proceed to
DTCs are not output A
DTC is output B



A

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

B

GO TO DTC CHART

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

e.

Read the values displayed on the GTS.

Standard:
Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE SPEED)

NG

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.

Powertrain > Hybrid Control > Data List
Tester Display
Vehicle Speed
50003 397 12

e.

Read the value displayed on the GTS.

Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DECELERATION SENSOR)

NG

INSPECT ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
50003 105 14,15

e.

Read the values displayed on the GTS.

Standard:
Condition Specified Condition
During deceleration Values change with vehicle speed
During acceleration Values change with vehicle speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

7.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from P to (D or S) or R.



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from R to (D or S), from (D or S) or N to R.

A396026E54
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 0.771,3.271 2.25,3.656 1.479,0.385 10 false Hybrid System Output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.438,4.125 7.094,4.74 2.656,0.615 10 false *: The hybrid system output restricted level differs between pattern A and pattern B.



·

Items Controlled

-

Hybrid system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is in P or N.



Reverse control

Activation conditions


·

The shift lever is in R.

·

The accelerator pedal is depressed excessively.

A396028E54
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 0.948,3.167 2.375,3.646 1.427,0.479 10 false Hybrid System Output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

Hybrid system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is moved to any position other than R.




HINT:
·

The hybrid system output restricted level differs between Pattern A, Pattern B and Reverse control.

·

During Shift control or Reverse control, hybrid system output is adjusted based on the road gradient.



Result:
Result Proceed to
Not performed A
Performed B


HINT:

If the customer operated the vehicle in a way which caused the drive start control to operate, explain the operation of the system to the customer and that the operation is not a malfunction.




A

8.CHECK DTC OUTPUT (HEALTH CHECK)

B

SYSTEM NORMAL

8.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC is output B


f.

Turn the power switch off.



A

9.INSPECT SHIFT LEVER POSITION SENSOR

B

GO TO DTC CHART

9.INSPECT SHIFT LEVER POSITION SENSOR

Result:
Result Proceed to
Normal A
Abnormal B



A

10.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

B

10.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

OK

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY