Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _062271 SEAT BELT _0303950 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Pretensioner and Force Limiter)


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 64330D 4.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

Hide 64910J 5.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 58410B 6.REMOVE DECK BOARD ASSEMBLY

Hide 64777J 7.REMOVE SPARE WHEEL CUSHION (for 2ZR-FXE)

Hide 64997 8.REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)

Hide 64995 9.REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)

Hide 64429B 10.REMOVE LUGGAGE ROOM BOX (for M20A-FXS with Spare Tire)

Hide 11.REMOVE SPARE TIRE (for M20A-FXS with Spare Tire)

Hide 58440 12.REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS without Spare Tire)

Hide 64991 13.REMOVE DECK FLOOR FRONT BOX (for M20A-FXS without Spare Tire)

Hide 67918A 14.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 71304C 16.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 76974F 17.REMOVE REAR UNDER SIDE COVER

Hide 62552F 18.REMOVE REAR SEAT SIDE GARNISH

Hide 64716D 19.REMOVE DECK TRIM REAR COVER

Hide 81330 20.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 64715C 21.REMOVE DECK TRIM SIDE COVER (w/ Cover)

Hide 64740C 22.REMOVE DECK TRIM SIDE PANEL ASSEMBLY

Hide 62480A 23.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

Hide 73370 24.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for LH Side)

a.
B458434

Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly LH.


b.

w/o Pretensioner and Force Limiter:

i.
B458439

Loosen the nut.


ii.
B458441

Remove the 3 bolts.


iii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH with bracket.


iv.
B458445

Remove the nut.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.



c.

w/ Pretensioner and Force Limiter:

i.
B458438

Loosen the nut.


ii.
B458440

Remove the 3 bolts.


iii.

Disengage the guides to separate the rear seat 3 point type outer belt assembly LH with bracket.


iv.
B458442C01
0.865,0.698 1.083,0.51 true 1.125,0.885 1.344,0.698 true 1.104,0.354 1.417,0.552 0.313,0.198 10 false *a 1.354,0.563 1.667,0.76 0.313,0.198 10 false *b
*a Locking Button
*b Protective Tape


Disengage the clamp.


v.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.


vi.
B458444

Remove the nut.


vii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.



Hide 73360 25.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for RH Side)

a.
B458435

Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly RH.


b.

w/o Pretensioner and Force Limiter:

i.
B458449

Loosen the nut.


ii.
B458451

Remove the 3 bolts.


iii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.


iv.
B460279

Remove the nut.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.



c.

w/ Pretensioner and Force Limiter:

i.
B458446C01
0.875,0.708 1.115,0.521 true 1.146,0.917 1.385,0.729 true 1.146,0.396 1.458,0.594 0.313,0.198 10 false *a 1.385,0.615 1.698,0.813 0.313,0.198 10 false *b
*a Locking Button
*b Protective Tape


Disengage the clamp.


ii.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.


iii.
B458449

Loosen the nut.


iv.
B458450

Remove the 3 bolts.


v.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.


vi.
B460280

Remove the nut.


vii.

Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.