Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.09
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404455 ENGINE UNIT A

M20A-FXS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the stiffening crankcase assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17169A 2.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 16032 3.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.

Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16031 4.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 11452D 5.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250E 8.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23250F 10.INSTALL PORT FUEL INJECTOR ASSEMBLY

Hide 23291 12.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23807 14.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 82126A 15.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 16.INSTALL SENSOR WIRE

a.

Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 3 clamps.


c.

Connect the 3 connectors.


Hide 17.INSTALL WATER BY-PASS HOSE ASSEMBLY

a.

Install the water by-pass hose assembly to the water inlet with thermostat sub-assembly and cylinder head sub-assembly and slide the 2 clips to secure them.


b.

Install the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23100X 18.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 19.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 20.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 21.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A426800C01
2.74,2.76 2.844,2.594 false 2.896,2.49 3.208,2.646 0.313,0.156 10 false *a 1.604,2.406 1.917,2.563 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23910A 22.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


c.

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 17177 23.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 16279 26.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet sub-assembly and slide the clip to secure it.


b.

Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 29.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 22271 30.INSTALL THROTTLE BODY GASKET

Hide 22030 31.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17167 33.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 23881E 34.INSTALL FUEL HOSE BRACKET

a.
A433787

Install the 2 fuel hose brackets to the cylinder head sub-assembly with the 2 bolts

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25760 35.INSTALL NO. 1 VACUUM PIPE

a.
A433547

Using a 14 mm union nut wrench, connect the No. 1 vacuum pipe to the exhaust manifold (TWC: Front Catalyst).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf)




b.

Install the No. 1 vacuum pipe to the exhaust manifold (TWC: Front Catalyst) with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16572D 36.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.