Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
Power seat is available only on the driver side.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
72108
1.INSTALL UPPER SEAT TRACK RAIL SUB-ASSEMBLY
85822B
2.INSTALL POWER SEAT TILT MOTOR ASSEMBLY
Install the power seat tilt motor assembly with the 3 bolts.
Bolt (A) is shorter than bolt (B). Make sure to install them to the correct positions.
85822C
3.INSTALL POWER SEAT LIFTER MOTOR ASSEMBLY
Install the power seat lifter motor assembly.
| *1 | Front Seat Vertical Housing Sub-assembly |
| *2 | Front Seat Adjuster Assembly |
| *a | Stud Bolt of the Front Seat Vertical Housing Sub-assembly |
| *b | Hole of the Front Seat Adjuster Assembly |
Install the front seat vertical housing sub-assembly.
Make sure to insert the stud bolt of the front seat vertical housing sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.
Make sure to position the front seat adjuster assembly so that when the front seat vertical housing sub-assembly is installed, their gears will be positioned as shown in the illustration.
Install the vertical adjuster spacer.
Install the front seat adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
71874C
4.INSTALL FRONT SEAT LOWER CUSHION SHIELD
|
Install in this direction (1) |
|
Install in this direction (2) |
Engage the guide (B) as shown in the illustration.
Engage the guide (A) as shown in the illustration.
Engage the claw to install the front seat lower cushion shield.
5.INSTALL SEAT POSITION AIRBAG SENSOR WITH BRACKET (w/ Seat Position Airbag Sensor)
72277A
6.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (w/ Seat Position Airbag Sensor)
87501B
7.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY
7181B
8.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER
|
Install in this direction |
Engage the claws and guides to install the front seat cushion wire harness holder as shown in the illustration.
Install the 2 screws.
71052A
9.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
82192
10.INSTALL FRONT SEAT WIRE
Engage the clamps to install the front seat wire.
Engage the claw and clamps.
Connect the 3 connectors.
Engage the clamp.
Connect the connector.
82192B
11.INSTALL NO. 2 FRONT SEAT WIRE (w/ Seat Position Airbag Sensor)
Engage the claw.
Engage the clamp to install the No. 2 front seat wire.
Connect the connector.
71874A
12.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
| *a | Hook |
| *b | Guide |
Engage the guide.
Engage the claw.
Engage the hook to install the front seat lower cushion shield LH.
71873A
13.INSTALL FRONT SEAT LOWER CUSHION SHIELD
| *a | Hook |
| *b | Guide |
Engage the guide.
Engage the claw.
Engage the hook to install the front seat lower cushion shield.
71876G
14.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH
Engage the claws to install the LH seat reclining adjuster inside cover LH.
Engage the claw.
71875G
15.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH
Engage the claws to install the LH seat reclining adjuster inside cover RH.
87510L
16.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY
71072S
17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
Be careful not to damage the separate type front seat cushion cover.
18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the hooks (A) and hooks (B) to install the separate type front seat cushion cover with pad.
Engage the clamp.
Connect the connector.
71759B
19.INSTALL FRONT SEATBACK HOOK
Engage the claws to install the 2 front seatback hooks to the front seatback frame sub-assembly.
8219B
20.INSTALL NO. 2 FRONT SEAT WIRE
Engage the clamps to install the No. 2 front seat wire.
79977A
21.INSTALL SEATBACK FELT
72760D
22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY
73920A
23.INSTALL FRONT SEAT AIRBAG ASSEMBLY
87510N
24.INSTALL FRONT SEATBACK HEATER ASSEMBLY
71074S
25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to damage the separate type front seatback cover.
26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
71931
27.INSTALL FRONT SEAT HEADREST SUPPORT
|
Install in this direction |
Engage the claws to install the 2 front seat headrest supports as shown in the illustration.
Close the 2 fasteners as shown in the illustration.
Engage the clamp.
Engage the hooks.
28.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
Engage the clamp.
Connect the connector.
Engage the clamp.
Connect the connector.
Engage the claw.
Engage the clamps to connect the front seat airbag assembly wire harness.
Engage the hooks.
Engage the hook.
84922C
29.INSTALL FRONT POWER SEAT SWITCH
72714
30.INSTALL SEAT ADJUSTER SHIELD CLAMP BRACKET
Install the seat adjuster shield clamp bracket with the 2 screws.
84921K
31.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the claws to install the reclining power seat switch knob.
84921D
32.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the claws to install the slide and vertical power seat switch knob.
71862
33.INSTALL FRONT SEAT INNER CUSHION SHIELD
|
Install in this direction |
Engage the claws to install the front seat inner cushion shield as shown in the illustration.
Engage the claws and guides.
71812D
34.INSTALL FRONT SEAT CUSHION SHIELD
Connect the connector.
|
Install in this direction (1) |
|
Install in this direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) to install the front seat cushion shield as shown in the illustration.
Engage the claws.
71868A
35.INSTALL NO. 1 FRONT SEAT INNER CUSHION SHIELD
|
Install in this direction |
Engage the claw and guides to install the No. 1 front seat inner cushion shield as shown in the illustration.
|
Install in this direction |
Engage the guide as shown in the illustration.
Install the clip.
71074S
36.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73240
37.INSTALL FRONT SEAT INNER BELT ASSEMBLY