Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU › from 2020.08
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0304145 CLEARANCE WARNING ECU A

PARK ASSIST / MONITORING  CLEARANCE WARNING ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during clearance warning ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Clearance warning ECU assembly
·

Measurement of ultrasonic sensor detection angle

·

Steering angle neutral point

·

Bumper type registration

·

Ultrasonic sensor detection angle registration


·

Toyota parking assist-sensor system

·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 55470 3.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55434B 7.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 55440D 8.REMOVE INSTRUMENT PANEL BOX ASSEMBLY

Hide 55406B 9.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

Hide 86841 10.REMOVE NAVIGATION ECU WITH BRACKET (w/ Navigation System)

Hide 82660B 11.SEPARATE RELAY BLOCK ASSEMBLY

a.
E357043

Remove the 2 nuts to separate the relay block assembly.


Hide 89343C 12.REMOVE NO. 1 CLEARANCE WARNING BUZZER

Hide 89340A 13.REMOVE CLEARANCE WARNING ECU ASSEMBLY

a.
E426311

Disconnect the connector.


b.

Remove the 2 screws.


c.

Disengage the guides to remove the clearance warning ECU assembly.