Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2020.08
RM32K0E _51 Engine / Hybrid System _059910 2ZR-FXE INTAKE / EXHAUST _0293911 EXHAUST MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17141 1.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket and a new EGR cooler gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.


c.

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the 3 bolts.


d.
A459680C07
0.073,0.052 0.427,0.292 0.354,0.24 12 false *A 0.042,2.427 0.323,2.677 0.281,0.25 12 false *B 1.958,0.292 2.156,0.49 0.198,0.198 10 true 1 1.479,0.146 1.677,0.344 0.198,0.198 10 true 2 0.354,0.25 0.469,0.427 0.115,0.177 10 true 7 0.198,0.75 0.385,0.948 0.188,0.198 10 true 6 1.021,0.865 1.188,1.063 0.167,0.198 10 true 4 2.656,2.583 2.854,2.781 0.198,0.198 10 true 3 3.042,2.813 3.24,3.063 0.198,0.25 10 true 5 1.958,2.594 2.156,2.792 0.198,0.198 10 true 1 1.25,2.563 1.448,2.76 0.198,0.198 10 true 2 1.063,3.188 1.229,3.385 0.167,0.198 10 true 4 0.177,3.083 0.365,3.281 0.188,0.198 10 true 6 0.313,2.563 0.479,2.771 0.167,0.208 10 true 7 2.583,0.115 2.781,0.313 0.198,0.198 10 true 3 3.031,0.417 3.229,0.667 0.198,0.25 10 true 5
*A w/o Differential Pressure Sensor
*B w/ Differential Pressure Sensor


Using a 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
A395537E01
0.26,1.188 0.417,1.385 0.156,0.198 10 true 3 2.885,1.469 3.042,1.667 0.156,0.198 10 true 1 2.823,0.5 2.979,0.698 0.156,0.198 10 true 2

Tighten the 3 bolts in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o Differential Pressure Sensor:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 6 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



b.

w/ Differential Pressure Sensor:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 17167 3.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 6 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket to the front suspension crossmember sub-assembly with the bolt and engage the 3 clamps.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Install the wiring harness clamp bracket to the cylinder head sub-assembly with the bolt and engage the clamp.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 25733A 5.INSTALL NO. 1 PIPE (w/ Differential Pressure Sensor)

a.

Temporarily install a new No. 1 pipe to the exhaust manifold with the nut.


b.

Tighten the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A459679C01
0.552,1 0.781,1.219 0.229,0.219 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, tighten the No. 1 pipe.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).




Hide 25715 6.INSTALL EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)

a.

Install the emission control valve bracket to the cylinder head sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.

Connect the vacuum transmitting hose assembly to the No. 1 pipe and slide the clip to secure it.


c.

Connect the differential pressure sensor connector.


d.

Engage the wire harness clamp.


Hide 7.INSTALL WIRING HARNESS CLAMP BRACKET (w/o Differential Pressure Sensor)

a.

Install the wiring harness clamp bracket to the cylinder head sub-assembly with the bolt and engage the clamp.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gaskets.

·

Do not damage the exhaust pipe gaskets.

·

Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C37
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Engage the wire harness clamp.


h.

Connect the heated oxygen sensor connector.


Hide 57533B 9.INSTALL FRONT FLOOR CENTER BRACE

a.

except GR SPORT:

i.

Install the 3 front center floor braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)



b.

for GR SPORT:

i.

Install the 2 front center floor braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)



Hide 58166 10.INSTALL FRONT FLOOR COVER LH

a.

Engage the 5 clamps to install the front floor cover LH to the vehicle body with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165B 11.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER