Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293922 ENGINE ASSEMBLY A

2ZR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 3.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 31270 5.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 82121 7.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


Hide 88370 10.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Hide 12305 11.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A372580C03
0.604,2.167 1.219,2.344 0.615,0.177 10 true 1 (*a), 3 3.01,1.719 3.208,1.906 0.198,0.188 10 true 2 2.094,0.333 2.323,0.542 0.229,0.208 10 true 4
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Connect the air conditioner tube and accessory assembly to the engine mounting insulator sub-assembly RH with the bolt and nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle body with the 2 bolts.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 12372A 12.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A372579C03
0.385,0.896 0.99,1.115 0.604,0.219 10 true 1 (*a), 5 2.896,1.896 3.094,2.083 0.198,0.188 10 true 2 0.667,1.885 0.844,2.063 0.177,0.177 10 true 3 2.719,1.021 2.927,1.219 0.208,0.198 10 true 4 2.208,0.073 2.458,0.271 0.25,0.198 10 true 6
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 4 bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 14.INSTALL WIRE HARNESS CLAMP BRACKET (w/o Differential Pressure Sensor)

a.

Install the wire harness clamp bracket with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


b.

Engage the 3 clamps.


Hide 89481B 15.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)

Hide 25715 16.INSTALL EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)

a.

Install the wire harness clamp bracket with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.

Engage the 3 clamps.


Hide 17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.

Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


d.
A397417C01
1.563,1.375 1.917,0.583 1.917,0.583 2.083,0.583 false 2.167,0.5 2.479,0.698 0.313,0.198 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads of bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.

Install the No. 2 engine mounting stay LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Install the engine mounting insulator LH to the hybrid vehicle transaxle assembly with the 3 bolts and nut.

Torque:
Bolt : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


g.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 51108A 18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17410 21.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 57533B 22.INSTALL FRONT FLOOR CENTER BRACE

Hide 58165B 24.INSTALL FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 45025D 25.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 26.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 27.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 82123 28.CONNECT NO. 3 ENGINE WIRE

a.
A393199C01
2.198,0.427 2.448,0.604 0.25,0.177 10 true *a 2.208,1.406 2.448,1.583 0.24,0.177 10 true *b
*a Bolt (A)
*b Bolt (B)


Connect the No. 3 engine wire to hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Engage the clamp.


Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 30.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide G922F 31.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.

Connect the outlet No. 1 hybrid water pump hose to the motor cooling cooler and slide the clip to secure it.


Hide G922H 32.CONNECT INLET HYBRID RADIATOR HOSE

a.

Connect the inlet hybrid radiator hose to the motor cooling cooler and slide the clip to secure it.


Hide 23901 33.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23826 34.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the fuel vapor feed pipe and slide the clip to secure it.


Hide 87245A 35.CONNECT INLET HEATER WATER HOSE A

a.

Connect the inlet heater water hose A to the EGR pipe with cooler sub-assembly and slide the clip to secure it.


Hide 87246 36.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the No. 1 water by-pass pipe and slide the clip to secure it.


Hide 16572D 37.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.


Hide 16573B 38.CONNECT NO. 3 RADIATOR HOSE

a.

Connect the No. 3 radiator hose to the water outlet and slide the clip to secure it.


b.

Install the 2 bolts to the hybrid vehicle transaxle assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 33820B 39.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the cylinder head cover sub-assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


c.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17751 41.INSTALL NO. 1 AIR CLEANER INLET

Hide 17701 43.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 44.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 22210 45.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17752 46.INSTALL NO. 2 AIR CLEANER INLET

Hide 16296 48.CONNECT NO. 8 WATER BY-PASS HOSE

a.

Connect the No. 8 water by-pass hose to the No. 2 water by-pass hose assembly and slide the clip to secure it.


Hide 50.ADD HYBRID TRANSAXLE FLUID

Hide 51.ADD ENGINE COOLANT (for Engine)

Hide 52.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 58.INSPECT FOR COOLANT LEAK (for Engine)

Hide 59.WARM UP COMPRESSOR

a.

Keep the A/C switch on for at least 2 minutes to warm up the compressor.

NOTICE:

To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).



Hide 51444A 64.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH to the vehicle with the 6 clips.


Hide 51443C 65.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH to the vehicle with the 6 clips.


Hide 51441 66.INSTALL NO. 1 ENGINE UNDER COVER

a.
A390450C02
0.854,0 1.083,0.198 0.229,0.198 10 true *1 1.396,0.01 1.625,0.208 0.229,0.198 10 true *1 1.875,0.01 2.104,0.208 0.229,0.198 10 true *1 2.417,0 2.646,0.198 0.229,0.198 10 true *1
*1 Bolt


Install the No. 1 engine under cover to the vehicle with the 4 bolts, 4 screws and 4 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67.INSTALL FRONT WHEELS

Hide 71.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT