Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2020.08
RM32K0E _52 Drivetrain _061337 AXLE AND DIFFERENTIAL _0299677 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY

a.

Secure the steering knuckle between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 3 bolts.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)

NOTICE:
·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.




Hide 2.INSTALL FRONT AXLE ASSEMBLY

a.
C362084C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


b.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
270 N*m (2753 kgf*cm, 199 ft.*lbf)

NOTICE:
·

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.

·

When installing the nuts, keep the bolts from rotating.



HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 43420 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.
C344863C03
2.781,0.427 3.208,0.427 3.208,0.427 3.208,1.656 true 2.885,0.688 3.208,0.688 true 3.156,1.667 3.396,1.896 0.24,0.229 10 false *a
*a Matchmark


Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and connect the front drive shaft assembly to the front axle assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the speed sensor rotor or contact surfaces.

·

Do not damage the front drive shaft outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the speed sensor rotor.




Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.

Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
89 N*m (908 kgf*cm, 66 ft.*lbf)


Hide 45047 5.CONNECT TIE ROD END SUB-ASSEMBLY

Hide 43215 6.INSTALL STEERING KNUCKLE SEAL (w/ Seal)

Hide 43512 7.INSTALL FRONT DISC

Hide 8.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 9.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm deep socket wrench, while applying the brakes, temporarily install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the front drive shaft from rotating.



Hide 10.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 11.REMOVE FRONT DISC

Hide 12.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 14.INSTALL FRONT DISC

Hide 15.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 89543 16.INSTALL FRONT SPEED SENSOR

a.
C365816

Set the 2 hooks of front speed sensor to the front shock absorber assembly.

NOTICE:

Do not twist the front speed sensor when installing it.



b.

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



c.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Prevent foreign matter from attaching to the front speed sensor tip.

·

Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.

·

After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.

·

Do not twist the front speed sensor when installing it.




d.

Engage the clamp.

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 17.STAKE FRONT AXLE SHAFT NUT

a.
C344869

Using a chisel and hammer, stake the front axle shaft nut.


Hide 18.INSTALL FRONT WHEEL

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 20.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 22. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART