When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY
Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.
Hold the rear axle carrier pin while rotating the nut.
Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.
2.INSTALL FLEXIBLE HOSE BRACKET
Install the flexible hose bracket to the rear axle carrier sub-assembly with the bolt.
48720A
3.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY
48258C
4.INSTALL REAR LOWER COIL SPRING INSULATOR
48231B
5.INSTALL REAR COIL SPRING
6.STABILIZE SUSPENSION
48790
7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY
Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48720A
8.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY
48740F
9.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48540
10.INSTALL REAR SHOCK ABSORBER ASSEMBLY
48840A
11.INSTALL REAR STABILIZER LINK ASSEMBLY
42450B
12.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY
13.CONNECT SKID CONTROL SENSOR WIRE
42431
14.INSTALL REAR DISC
for TMC Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>INSTALLATION
for TMMT Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>INSTALLATION
15.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
89408C
16.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
17.INSTALL REAR WHEEL
48740F
18.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Connect the reservoir level switch connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
Turn the power switch on (READY).
Depress the brake pedal and release it.
Clear the DTCs.
20.INSPECT AND ADJUST REAR WHEEL ALIGNMENT
21.CHECK FOR SPEED SENSOR SIGNAL
22.PERFORM INITIALIZATION (w/ Height Control Sensor)
23. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART