Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › 2020.08–2022.01
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303881 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 side airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 67918A 4.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 5.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.


Hide 76974F 6.REMOVE REAR UNDER SIDE COVER

Hide 71304C 7.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 62552F 8.REMOVE REAR SEAT SIDE GARNISH

Hide 89831C 9.REMOVE NO. 2 SIDE AIRBAG SENSOR

a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B458403

Remove the bolt and disengage the claw to separate the No. 2 side airbag sensor.


d.

Disconnect the connector to remove the No. 2 side airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

C195226C40
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 true 0.948,1.156 0.417,0.729 true 3.469,1.146 2.938,0.74 true 3.625,1.042 3.427,0.667 true 1.125,1.042 0.833,0.604 true 0.667,0.406 0.854,0.583 0.188,0.177 10 false *a 3.313,0.469 3.5,0.646 0.188,0.177 10 false *a 1.313,2.208 1.5,2.385 0.188,0.177 10 false *b 0.969,1.708 1.156,1.885 0.188,0.177 10 false *c 3.531,1.729 3.719,1.906 0.188,0.177 10 false *c 3.823,2.177 4.01,2.354 0.188,0.177 10 false *b 1.427,0.625 1.615,0.802 0.188,0.177 10 false *d 3.875,0.646 4.063,0.823 0.188,0.177 10 false *d 2.719,0.542 2.969,0.729 0.25,0.188 10 false (A) 0.26,0.5 0.51,0.688 0.25,0.188 10 false (A)
*a White Housing Lock *b Yellow CPA
*c Slide *d Push



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




e.

After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect