Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Telematics transceiver

(w/ Telematics Transceiver)

·

Radio and display receiver assembly

(for Radio and Display Type)

·

Central gateway ECU (network gateway ECU)

·

No. 3 CAN junction connector



WIRING DIAGRAM

for Radio and Display Type with Dual Knob Type


C360943E07
0.677,0.969 1.448,1.167 0.771,0.198 10 false 120 Ω 0.677,3.156 1.448,3.354 0.771,0.198 10 false 120 Ω 1.375,0.625 2.146,0.823 0.771,0.198 10 false CA3H 1.875,0.625 2.646,0.823 0.771,0.198 10 false 6 2.823,0.625 3.594,0.823 0.771,0.198 10 false 10 1.844,1.146 2.615,1.344 0.771,0.198 10 false 21 1.396,1.146 2.167,1.344 0.771,0.198 10 false CA3L 2.823,1.146 3.594,1.344 0.771,0.198 10 false 21 4.198,0.615 4.969,0.813 0.771,0.198 10 false 8 4.156,1.135 4.927,1.333 0.771,0.198 10 false 19 5.167,0.625 5.938,0.823 0.771,0.198 10 false 15 5.156,1.146 5.927,1.344 0.771,0.198 10 false 16 5.427,0.698 6.198,0.896 0.771,0.198 10 false CANP 5.427,1.24 6.198,1.438 0.771,0.198 10 false CANN 5.448,2.833 6.219,3.031 0.771,0.198 10 false CANH 5.146,3.281 5.917,3.479 0.771,0.198 10 false 14 5.146,2.76 5.917,2.958 0.771,0.198 10 false 13 5.458,3.354 6.229,3.552 0.771,0.198 10 false CANL 5.208,3.771 5.979,3.969 0.771,0.198 10 false F131 5.208,3.958 6.948,4.354 1.74,0.396 10 false Radio and Display Receiver Assembly 2.813,3.979 4.823,4.323 2.01,0.344 10 false No. 3 CAN Junction Connector 2.823,3.813 3.594,4.01 0.771,0.198 10 false F114 2.833,3.292 3.604,3.49 0.771,0.198 10 false 22 2.833,2.76 3.604,2.958 0.771,0.198 10 false 11 4.177,2.75 4.948,2.948 0.771,0.198 10 false 9 4.167,3.281 4.938,3.479 0.771,0.198 10 false 20 1.823,3.292 2.594,3.49 0.771,0.198 10 false 20 1.833,2.75 2.604,2.948 0.771,0.198 10 false 19 1.333,2.75 2.104,2.948 0.771,0.198 10 false CAYH 1.354,3.292 2.125,3.49 0.771,0.198 10 false CAYL 0.229,3.781 1,3.979 0.771,0.198 10 false F74 0.229,3.958 2.208,4.396 1.979,0.438 10 false Central Gateway ECU (Network Gateway ECU) 0.229,5 3.292,5.333 3.063,0.333 10 false *1: w/ Telematics Transceiver 5.156,1.646 5.927,1.844 0.771,0.198 10 false F165 5.146,1.823 6.708,2.198 1.563,0.375 10 false Telematics Transceiver*1


for Radio and Display Type with Single Knob Type


C360943E14
0.677,0.969 1.448,1.167 0.771,0.198 10 false 120 Ω 0.677,3.156 1.448,3.354 0.771,0.198 10 false 120 Ω 1.375,0.625 2.146,0.823 0.771,0.198 10 false CA3H 1.875,0.625 2.646,0.823 0.771,0.198 10 false 6 2.823,0.625 3.594,0.823 0.771,0.198 10 false 10 1.844,1.146 2.615,1.344 0.771,0.198 10 false 21 1.396,1.146 2.167,1.344 0.771,0.198 10 false CA3L 2.823,1.146 3.594,1.344 0.771,0.198 10 false 21 4.198,0.615 4.969,0.813 0.771,0.198 10 false 8 4.156,1.135 4.927,1.333 0.771,0.198 10 false 19 5.167,0.625 5.938,0.823 0.771,0.198 10 false 25 5.156,1.146 5.927,1.344 0.771,0.198 10 false 26 5.427,0.698 6.198,0.896 0.771,0.198 10 false CANP 5.427,1.24 6.198,1.438 0.771,0.198 10 false CANN 5.448,2.833 6.219,3.031 0.771,0.198 10 false CANH 5.146,3.281 5.917,3.479 0.771,0.198 10 false 14 5.146,2.76 5.917,2.958 0.771,0.198 10 false 13 5.458,3.354 6.229,3.552 0.771,0.198 10 false CANL 5.208,3.771 5.979,3.969 0.771,0.198 10 false F174 5.208,3.958 6.948,4.354 1.74,0.396 10 false Radio and Display Receiver Assembly 2.813,3.979 4.823,4.323 2.01,0.344 10 false No. 3 CAN Junction Connector 2.823,3.813 3.594,4.01 0.771,0.198 10 false F114 2.833,3.292 3.604,3.49 0.771,0.198 10 false 22 2.833,2.76 3.604,2.958 0.771,0.198 10 false 11 4.177,2.75 4.948,2.948 0.771,0.198 10 false 9 4.167,3.281 4.938,3.479 0.771,0.198 10 false 20 1.823,3.292 2.594,3.49 0.771,0.198 10 false 20 1.833,2.75 2.604,2.948 0.771,0.198 10 false 19 1.333,2.75 2.104,2.948 0.771,0.198 10 false CAYH 1.354,3.292 2.125,3.49 0.771,0.198 10 false CAYL 0.229,3.781 1,3.979 0.771,0.198 10 false F74 0.229,3.958 2.208,4.396 1.979,0.438 10 false Central Gateway ECU (Network Gateway ECU) 0.229,5 3.292,5.333 3.063,0.333 10 false *1: w/ Telematics Transceiver 5.156,1.646 5.927,1.844 0.771,0.198 10 false F175 5.146,1.823 6.708,2.198 1.563,0.375 10 false Telematics Transceiver*1


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425191C31
5.5,1 6,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.417,2.177 6.594,2.781 true 2.729,0.823 2.375,1.865 true 2.958,1.063 2.5,1.885 true 3.01,1.323 2.625,1.875 true 2.99,2.5 2.625,2.031 true 2.625,3.021 2.365,2.042 true 2.833,2.802 2.49,2.042 true 2.677,0.427 2.229,1.854 true 2.615,3.323 2.24,2.063 true 2.771,0.667 3.688,0.865 0.917,0.198 10 false CANH*c 2.677,2.969 3.594,3.167 0.917,0.198 10 false CANL*c 1.833,1.115 2.479,1.313 0.646,0.198 10 false F114 5.583,1.031 6.229,1.229 0.646,0.198 10 false F144 6.604,2.802 7.073,3.073 0.469,0.271 10 false BAT 3.021,0.906 3.938,1.104 0.917,0.198 10 false CANH*d 3.063,1.219 3.979,1.417 0.917,0.198 10 false CANH*d 2.906,2.74 3.823,2.938 0.917,0.198 10 false CANL*d 3.031,2.438 3.948,2.635 0.917,0.198 10 false CANL*d 0.156,0.125 0.802,0.323 0.646,0.198 10 false *a 4.51,0.115 5.156,0.313 0.646,0.198 10 false *1 2.75,0.302 3.667,0.5 0.917,0.198 10 false CANH*b 2.667,3.24 3.583,3.438 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Telematics Transceiver
(w/ Telematics Transceiver)
*c to Radio and Display Receiver Assembly
(for Radio and Display Type)
*d to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F114-8 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Telematics Transceiver*1
F114-19 (CANL) - F144-16 (BAT)
F114-9 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Radio and display receiver assembly*2
F114-20 (CANL) - F144-16 (BAT)
F114-10 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
F114-21 (CANL) - F144-16 (BAT)
F114-11 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
F114-22 (CANL) - F144-16 (BAT)


*1: w/ Telematics Transceiver

*2: for Radio and Display Type



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C32
5.5,1 6,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.417,2.167 6.583,2.667 true 3.01,1.063 2.5,1.875 true 2.635,1.875 3.021,1.438 true 2.646,2.031 3.01,2.417 true 3.021,2.719 2.5,2.042 true 3.063,0.948 3.979,1.146 0.917,0.198 10 false CANH*b 3.063,2.354 3.979,2.552 0.917,0.198 10 false CANL*b 1.854,1.125 2.5,1.323 0.646,0.198 10 false F114 5.594,1.031 6.24,1.229 0.646,0.198 10 false F144 6.635,2.625 7.052,2.854 0.417,0.229 10 false BAT 0.177,0.135 1.094,0.333 0.917,0.198 10 false *a 4.563,0.135 5.479,0.333 0.917,0.198 10 false *1 3.052,2.667 3.969,2.865 0.917,0.198 10 false CANL*b 3.052,1.281 3.969,1.479 0.917,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F114-10 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F114-21 (CANL) - F144-16 (BAT)
F114-11 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F114-22 (CANL) - F144-16 (BAT)



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425196C06
5.083,0.5 5.583,0.75 0.5,0.25 1.667,0.417 2.167,0.667 0.5,0.25 6,2.167 5.958,1.708 true 1.51,1.302 1.24,0.583 true 1.333,2.198 1.542,1.458 true 0.833,0.49 1.448,0.688 0.615,0.198 10 false CA3H 0.948,2.135 1.563,2.333 0.615,0.198 10 false CA3L 1.771,0.458 2.385,0.656 0.615,0.198 10 false F74 5.167,0.542 5.781,0.74 0.615,0.198 10 false F144 4.042,0.083 4.656,0.281 0.615,0.198 10 false *1 0.125,0.083 0.74,0.281 0.615,0.198 10 false *a 6.021,2.146 6.635,2.344 0.615,0.198 10 false BAT
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-6 (CA3H) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-21 (CA3L) - F144-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR