There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. | ·
Short to ground in CAN main bus line ·
Short to ground in CAN branch line ·
Telematics transceiver (w/ Telematics Transceiver) ·
Radio and display receiver assembly (for Radio and Display Type) ·
Central gateway ECU (network gateway ECU) ·
No. 3 CAN junction connector |
for Radio and Display Type with Dual Knob Type
for Radio and Display Type with Single Knob Type
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Telematics Transceiver
(w/ Telematics Transceiver) |
| *c | to Radio and Display Receiver Assembly
(for Radio and Display Type) |
*d | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F114-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Telematics Transceiver*1 |
| F114-19 (CANL) - F144-4 (CG) | |||
| F114-9 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Radio and display receiver assembly*2 |
| F114-20 (CANL) - F144-4 (CG) | |||
| F114-10 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| F114-21 (CANL) - F144-4 (CG) | |||
| F114-11 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| F114-22 (CANL) - F144-4 (CG) |
*1: w/ Telematics Transceiver
*2: for Radio and Display Type
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F114-10 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F114-21 (CANL) - F144-4 (CG) | ||
| F114-11 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F114-22 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-6 (CA3H) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-21 (CA3L) - F144-4 (CG) |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG