There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. | ·
Short to ground in CAN main bus line ·
Short to ground in CAN branch line ·
Hybrid vehicle control ECU ·
Central gateway ECU (network gateway ECU) ·
Inverter with converter assembly ·
ECM ·
Brake booster with master cylinder assembly ·
Battery ECU assembly (for LITHIUM-ION BATTERY) ·
Vehicle Approaching Speaker Controller (w/ Acoustic Vehicle Alerting System) ·
No. 5 CAN junction connector (for LHD) ·
No. 4 CAN junction connector (for RHD) ·
No. 2 CAN junction connector ·
No. 6 CAN junction connector |
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD with TMC Made | B |
| for RHD with TMMT Made | C |
A
B
C
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Hybrid Vehicle Control ECU |
| *e | to Inverter with Converter Assembly | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F124-7 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 6 CAN junction connector |
| F124-18 (CANL) - F144-4 (CG) | |||
| F124-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F124-19 (CANL) - F144-4 (CG) | |||
| F124-9 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Hybrid vehicle control ECU |
| F124-20 (CANL) - F144-4 (CG) | |||
| F124-10 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inverter with converter assembly |
| F124-21 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F124-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F124-19 (CANL) - F144-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to No. 5 CAN Junction Connector | *d | to Battery ECU Assembly
(for Lithium-ion Battery) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-1 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 2 CAN junction connector |
| M104-12 (CANL) - F144-4 (CG) | |||
| M104-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 5 CAN Junction Connector |
| M104-13 (CANL) - F144-4 (CG) | |||
| M104-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Battery ECU Assembly*1 |
| M104-14 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 CAN junction connector) | B |
| NG (Line to No. 2 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Vehicle Approaching Speaker Controller |
| *c | to ECM | *d | to Brake Booster with Master Cylinder Assembly |
| *e | to No. 6 CAN Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-1 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 kΩ or higher | Vehicle approaching speaker controller |
| F113-12 (CANL) - F144-4 (CG) | |||
| F113-4 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| F113-15 (CANL) - F144-4 (CG) | |||
| F113-5 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly |
| F113-16 (CANL) - F144-4 (CG) | |||
| F113-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 6 CAN Junction Connector |
| F113-17 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 6 CAN junction connector) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Booster with Master Cylinder Assembly |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F115-7 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| F115-18 (CANL) - F144-4 (CG) | |||
| F115-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F115-19 (CANL) - F144-4 (CG) | |||
| F115-9 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly |
| F115-20 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F115-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F115-19 (CANL) - F144-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to Hybrid vehicle control ECU |
| *c | to Inverter with converter assembly | *d | to ECM |
| *e | to No. 4 CAN Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Hybrid vehicle control ECU |
| F113-13 (CANL) - F144-4 (CG) | |||
| F113-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inverter with converter assembly |
| F113-14 (CANL) - F144-4 (CG) | |||
| F113-4 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| F113-15 (CANL) - F144-4 (CG) | |||
| F113-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 4 CAN Junction Connector |
| F113-17 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 4 CAN junction connector) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-18 (CA4H) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-17 (CA4L) - F144-4 (CG) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Brake Booster with Master Cylinder Assembly |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F115-7 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| F115-18 (CANL) - F144-4 (CG) | |||
| F115-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F115-19 (CANL) - F144-4 (CG) | |||
| F115-9 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly |
| F115-20 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F115-8 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F115-19 (CANL) - F144-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to No. 4 CAN Junction Connector | *d | to Battery ECU Assembly
(for Lithium-ion Battery) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-1 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 2 CAN junction connector |
| M104-12 (CANL) - F144-4 (CG) | |||
| M104-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| M104-13 (CANL) - F144-4 (CG) | |||
| M104-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Battery ECU Assembly*1 |
| M104-14 (CANL) - F144-4 (CG) |
*1: for LITHIUM-ION BATTERY
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 4 CAN junction connector) | B |
| NG (Line to No. 2 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Vehicle Approaching Speaker Controller |
| *c | to Hybrid Vehicle Control ECU | *d | to Inverter with Converter Assembly |
| *e | to ECM | *f | to No. 6 CAN junction connector |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-1 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 kΩ or higher | Vehicle Approaching Speaker Controller |
| F113-12 (CANL) - F144-4 (CG) | |||
| F113-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Hybrid vehicle control ECU |
| F113-13 (CANL) - F144-4 (CG) | |||
| F113-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Inverter with converter assembly |
| F113-14 (CANL) - F144-4 (CG) | |||
| F113-4 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| F113-15 (CANL) - F144-4 (CG) | |||
| F113-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 6 CAN junction connector |
| F113-17 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 6 CAN junction connector) | B |
| NG (Line to ECU or sensor) | C |
A
B
C