Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

Hybrid vehicle control ECU

·

Central gateway ECU (network gateway ECU)

·

Brake booster with master cylinder assembly

·

Airbag sensor assembly

·

Steering sensor

·

Power steering ECU assembly

·

Brake actuator assembly

·

No. 4 CAN junction connector

·

No. 5 CAN junction connector



WIRING DIAGRAM

for LHD


C366144E03
1.344,0.708 1.958,0.906 0.615,0.198 10 false CA3P 1.354,1.25 1.969,1.448 0.615,0.198 10 false CA3N 1.333,3.99 1.948,4.188 0.615,0.198 10 false CAN+ 1.375,4.531 1.99,4.729 0.615,0.198 10 false CAN- 5.271,4 5.885,4.198 0.615,0.198 10 false CA1H 5.271,4.531 5.885,4.729 0.615,0.198 10 false CA1L 5.271,1.146 5.885,1.344 0.615,0.198 10 false CA2L 5.271,0.615 5.885,0.813 0.615,0.198 10 false CA2H 1.865,0.615 2.594,0.844 0.729,0.229 10 false 31*1 7*2 1.854,1.146 2.604,1.344 0.75,0.198 10 false 30*1 20*2 1.875,3.896 2.667,4.083 0.792,0.188 10 false 31*1 7*2 1.875,4.438 2.854,4.646 0.979,0.208 10 false 32*1 17*2 2.698,0.615 3.313,0.813 0.615,0.198 10 false 3 2.625,1.146 3.24,1.344 0.615,0.198 10 false 14 4.01,0.615 4.625,0.813 0.615,0.198 10 false 2 4.01,1.146 4.625,1.344 0.615,0.198 10 false 13 4.01,1.448 4.625,1.646 0.615,0.198 10 false 12 4.01,1.719 4.625,1.917 0.615,0.198 10 false 1 2.792,2.198 3.406,2.396 0.615,0.198 10 false F124 0.396,1.604 1.385,1.771 0.99,0.167 10 false F3*1 F160*2 0.396,1.771 2.271,2.135 1.875,0.365 10 false Hybrid Vehicle Control ECU 2.792,2.365 4.031,2.969 1.24,0.604 10 false No. 5 CAN Junction Connector 4.969,0.615 5.583,0.813 0.615,0.198 10 false 22 5.042,1.146 5.656,1.344 0.615,0.198 10 false 7 5.906,0.99 6.677,1.188 0.771,0.198 10 false 120 Ω 4.854,1.625 5.469,1.823 0.615,0.198 10 false F74 4.854,1.792 6.833,2.219 1.979,0.427 10 false Central Gateway ECU (Network Gateway ECU) 4.01,3.333 4.625,3.531 0.615,0.198 10 false 7 4.01,3.594 4.625,3.792 0.615,0.198 10 false 17 4.01,3.896 4.625,4.094 0.615,0.198 10 false 3 4.01,4.438 4.625,4.635 0.615,0.198 10 false 13 2.708,3.896 3.323,4.094 0.615,0.198 10 false 4 2.635,4.438 3.25,4.635 0.615,0.198 10 false 14 4.969,3.896 5.583,4.094 0.615,0.198 10 false 43 4.969,4.438 5.583,4.635 0.615,0.198 10 false 42 0.844,4.917 1.958,5.167 1.115,0.25 10 false C63*1 A96*2 0.854,5.083 1.469,5.281 0.615,0.198 10 false ECM 4.844,4.917 5.458,5.115 0.615,0.198 10 false A39 4.844,5.083 6.531,5.521 1.688,0.438 10 false Brake Booster with Master Cylinder Assembly 4.042,5.792 5.271,6.385 1.229,0.594 10 false No. 4 CAN Junction Connector 4.042,5.635 4.656,5.833 0.615,0.198 10 false F116 0.5,6.333 2.792,6.531 2.292,0.198 10 false *1: for 2ZR-FXE 1.708,6.333 4,6.531 2.292,0.198 10 false *2: for M20A-FXS

C366145E07
1.333,1.49 1.948,1.688 0.615,0.198 10 false CANH 1.333,2.031 1.948,2.229 0.615,0.198 10 false CANL 5.448,1.49 6.063,1.688 0.615,0.198 10 false CANH 5.448,2.031 6.063,2.229 0.615,0.198 10 false CANL 1.854,1.396 2.167,1.594 0.313,0.198 10 false 12 1.854,1.927 2.167,2.125 0.313,0.198 10 false 11 1.333,3.531 1.948,3.729 0.615,0.198 10 false CANH 5.448,3.625 6.063,3.823 0.615,0.198 10 false CANH 1.344,4.073 1.958,4.271 0.615,0.198 10 false CANL 5.448,4.167 6.063,4.365 0.615,0.198 10 false CANL 0.521,2.552 2.635,2.802 2.115,0.25 10 false Brake Actuator Assembly 0.521,2.406 1.135,2.604 0.615,0.198 10 false A85 2.875,1.396 3.188,1.594 0.313,0.198 10 false 2 2.802,1.917 3.115,2.115 0.313,0.198 10 false 12 4.188,1.927 4.5,2.125 0.313,0.198 10 false 16 4.188,1.396 4.5,1.594 0.313,0.198 10 false 6 5.219,1.927 5.531,2.125 0.313,0.198 10 false 8 5.219,1.396 5.531,1.594 0.313,0.198 10 false 7 5.219,3.531 5.531,3.729 0.313,0.198 10 false 3 5.219,4.073 5.531,4.271 0.313,0.198 10 false 2 4.188,3.531 4.5,3.729 0.313,0.198 10 false 5 4.188,4.073 4.5,4.271 0.313,0.198 10 false 15 2.813,4.073 3.125,4.271 0.313,0.198 10 false 11 2.885,3.531 3.198,3.729 0.313,0.198 10 false 1 1.854,4.073 2.167,4.271 0.313,0.198 10 false 27 1.854,3.531 2.167,3.729 0.313,0.198 10 false 26 0.688,3.906 1.302,4.104 0.615,0.198 10 false 120 Ω 4.927,2.542 7.042,2.792 2.115,0.25 10 false Power Steering ECU Assembly 4.927,2.375 5.354,2.604 0.427,0.229 10 false F23 0.375,4.719 2.49,4.969 2.115,0.25 10 false Airbag Sensor Assembly 0.375,4.552 0.875,4.781 0.5,0.229 10 false F150 5.406,4.708 6.563,5.01 1.156,0.302 10 false Steering Sensor 5.406,4.552 5.938,4.74 0.531,0.188 10 false F69 2.969,4.719 4.198,5.156 1.229,0.438 10 false No. 4 CAN Junction Connector 2.969,4.552 3.49,4.802 0.521,0.25 10 false F116


for RHD


C366147E13
1.333,0.708 1.948,0.906 0.615,0.198 10 false CAN+ 1.375,1.25 1.99,1.448 0.615,0.198 10 false CAN- 1.854,0.615 2.552,0.823 0.698,0.208 10 false 31*1 7*2 1.854,1.146 2.667,1.323 0.813,0.177 10 false 32*1 17*2 1.844,3.688 2.573,3.885 0.729,0.198 10 false 31*1 7*2 1.854,4.219 2.604,4.417 0.75,0.198 10 false 30*1 20*2 1.354,3.781 1.969,3.979 0.615,0.198 10 false CA3P 1.354,4.323 1.969,4.521 0.615,0.198 10 false CA3N 5.26,0.615 5.875,0.813 0.615,0.198 10 false CA2H 5.26,1.146 5.875,1.344 0.615,0.198 10 false CA2L 5.25,2.854 5.865,3.052 0.615,0.198 10 false CANH 5.25,3.385 5.865,3.583 0.615,0.198 10 false CANL 2.698,1.146 3.313,1.344 0.615,0.198 10 false 9 2.688,0.615 3.302,0.813 0.615,0.198 10 false 3 3.99,1.146 4.385,1.323 0.396,0.177 10 false 8 3.99,0.615 4.469,0.813 0.479,0.198 10 false 2 3.99,2.75 4.438,2.948 0.448,0.198 10 false 6 3.99,3.292 4.375,3.49 0.385,0.198 10 false 12 3.99,3.688 4.427,3.865 0.438,0.177 10 false 1 3.99,4.219 4.438,4.427 0.448,0.208 10 false 7 2.688,3.688 3.302,3.885 0.615,0.198 10 false 4 2.615,4.219 3.229,4.417 0.615,0.198 10 false 10 2.771,4.708 3.385,4.906 0.615,0.198 10 false F178 2.771,4.875 4.042,5.292 1.271,0.417 10 false No. 5 CAN Junction Connector 0.385,4.865 2.229,5.271 1.844,0.406 10 false Hybrid Vehicle Control ECU 0.385,4.698 1.427,4.885 1.042,0.188 10 false F3*1 F160*2 0.854,1.792 1.219,2.052 0.365,0.26 10 false ECM 0.844,1.625 1.792,1.865 0.948,0.24 10 false C63*1 A96*2 4.948,0.615 5.344,0.792 0.396,0.177 10 false 22 5.021,1.146 5.417,1.323 0.396,0.177 10 false 7 4.792,1.604 5.406,1.802 0.615,0.198 10 false F74 4.792,1.771 6.781,2.198 1.99,0.427 10 false Central Gateway ECU (Network Gateway ECU) 4.948,2.75 5.208,3 0.26,0.25 10 false 12 4.948,3.292 5.385,3.5 0.438,0.208 10 false 11 5.115,3.771 5.729,3.969 0.615,0.198 10 false A84 5.115,3.938 6.844,4.177 1.729,0.24 10 false Brake Actuator Assembly 5.896,0.979 6.427,1.198 0.531,0.219 10 false 120 Ω 0.5,5.333 2.792,5.531 2.292,0.198 10 false *1: for 2ZR-FXE 1.75,5.333 4.042,5.531 2.292,0.198 10 false *2: for M20A-FXS 0.135,0.083 2.708,0.323 2.573,0.24 12 false for TMMT Made: 4.521,5.344 4.688,5.552 0.167,0.208 10 false A 4.844,5.354 5.01,5.563 0.167,0.208 10 false B

C366148E09
1.344,1.552 1.958,1.75 0.615,0.198 10 false CA1H 1.344,2.094 1.958,2.292 0.615,0.198 10 false CA1L 1.333,3.594 1.948,3.792 0.615,0.198 10 false CANH 1.344,4.135 1.958,4.333 0.615,0.198 10 false CANL 1.865,1.458 2.292,1.646 0.427,0.188 10 false 43 1.865,1.99 2.344,2.177 0.479,0.188 10 false 42 1.865,3.594 2.26,3.802 0.396,0.208 10 false 26 1.854,4.125 2.396,4.323 0.542,0.198 10 false 27 2.604,1.99 2.948,2.188 0.344,0.198 10 false 13 2.604,4.135 2.938,4.323 0.333,0.188 10 false 12 2.677,3.594 3.052,3.781 0.375,0.188 10 false 1 2.677,1.458 3.063,1.656 0.385,0.198 10 false 2 3.99,0.781 4.396,0.969 0.406,0.188 10 false 17 3.99,1.115 4.385,1.313 0.396,0.198 10 false 6 3.99,1.458 4.479,1.635 0.49,0.177 10 false 5 3.99,1.99 4.448,2.177 0.458,0.188 10 false 16 3.99,3.594 4.5,3.771 0.51,0.177 10 false 3 3.99,4.135 4.458,4.333 0.469,0.198 10 false 14 5.021,4.135 5.281,4.333 0.26,0.198 10 false 8 5.021,3.594 5.375,3.792 0.354,0.198 10 false 7 5.021,1.99 5.427,2.188 0.406,0.198 10 false 2 5.021,1.458 5.354,1.667 0.333,0.208 10 false 3 5.25,1.552 5.865,1.75 0.615,0.198 10 false CANH 5.25,3.698 5.865,3.896 0.615,0.198 10 false CANH 5.25,4.229 5.865,4.427 0.615,0.198 10 false CANL 5.25,2.094 5.865,2.292 0.615,0.198 10 false CANL 5.208,2.479 5.823,2.677 0.615,0.198 10 false F69 5.073,4.781 6.385,5.229 1.313,0.448 10 false Power Steering ECU Assembly 5.073,4.615 5.688,4.813 0.615,0.198 10 false F23 0.438,4.615 1.052,4.813 0.615,0.198 10 false F150 0.438,4.781 2.073,5.292 1.635,0.51 10 false Airbag Sensor Assembly 0.427,2.635 2.115,3.052 1.688,0.417 10 false Brake Booster with Master Cylinder Assembly 0.427,2.469 1.042,2.667 0.615,0.198 10 false A39 5.208,2.635 6.333,2.917 1.125,0.281 10 false Steering Sensor 2.76,4.615 3.375,4.813 0.615,0.198 10 false F115 2.76,4.771 4.052,5.292 1.292,0.521 10 false No. 4 CAN Junction Connector 0.677,3.99 1.292,4.188 0.615,0.198 10 false 120 Ω 0.188,0.135 2.323,0.594 2.135,0.458 12 false for TMMT Made: 4.521,0.302 4.927,0.49 0.406,0.188 10 false A 4.844,0.302 5.25,0.49 0.406,0.188 10 false B

C422279E12
1.365,0.969 1.979,1.167 0.615,0.198 10 false CAN+ 1.375,1.5 1.99,1.698 0.615,0.198 10 false CAN- 1.844,0.844 2.542,1.052 0.698,0.208 10 false 31*1 7*2 1.823,1.385 2.635,1.563 0.813,0.177 10 false 32*1 17*2 1.823,3.375 2.521,3.583 0.698,0.208 10 false 31*1 7*2 1.823,3.896 2.51,4.115 0.688,0.219 10 false 30*1 20*2 1.396,3.51 2.01,3.708 0.615,0.198 10 false CA3P 1.396,4.063 2.01,4.26 0.615,0.198 10 false CA3N 5.229,0.854 5.844,1.052 0.615,0.198 10 false CA2H 2.635,1.354 3.25,1.552 0.615,0.198 10 false 13 2.698,0.844 3.313,1.042 0.615,0.198 10 false 3 3.969,1.375 4.365,1.552 0.396,0.177 10 false 12 3.958,0.813 4.438,1.01 0.479,0.198 10 false 2 3.969,3.365 4.406,3.542 0.438,0.177 10 false 1 2.708,3.406 3.323,3.604 0.615,0.198 10 false 4 2.646,3.906 3.26,4.104 0.615,0.198 10 false 14 2.729,4.448 3.344,4.646 0.615,0.198 10 false F118 2.719,4.615 4.802,4.833 2.083,0.219 10 false No. 5 CAN Junction Connector 0.427,4.615 2.271,5.021 1.844,0.406 10 false Hybrid Vehicle Control ECU 0.427,4.417 1.5,4.646 1.073,0.229 10 false F3*1 F160*2 0.854,2.063 1.219,2.323 0.365,0.26 10 false ECM 0.844,1.865 1.792,2.104 0.948,0.24 10 false C63*1 A96*2 4.99,0.854 5.385,1.031 0.396,0.177 10 false 22 5.052,1.375 5.448,1.552 0.396,0.177 10 false 7 4.906,1.813 5.521,2.01 0.615,0.198 10 false F74 4.885,2 6.875,2.427 1.99,0.427 10 false Central Gateway ECU (Network Gateway ECU) 3.958,3.875 4.396,4.083 0.438,0.208 10 false 11 5.865,1.208 6.396,1.427 0.531,0.219 10 false 120 Ω 0.458,5.333 2.75,5.531 2.292,0.198 10 false *1: for 2ZR-FXE 1.75,5.333 4.042,5.531 2.292,0.198 10 false *2: for M20A-FXS 0.135,0.083 2.708,0.323 2.573,0.24 12 false for TMC Made: 5.24,1.375 5.854,1.573 0.615,0.198 10 false CA2L 5.531,5.083 5.698,5.323 0.167,0.24 10 false A 5.844,5.104 6.01,5.344 0.167,0.24 10 false B

C422280E02
0.167,0.104 2.552,0.344 2.385,0.24 12 false for TMC Made: 5.219,1.635 5.833,1.833 0.615,0.198 10 false CANH 5.24,2.146 5.854,2.344 0.615,0.198 10 false CANL 5.219,2.542 5.677,2.74 0.458,0.198 10 false F69 5.208,2.719 6.25,2.938 1.042,0.219 10 false Steering Sensor 5.24,5.667 5.854,5.865 0.615,0.198 10 false CANH 5.25,6.208 5.865,6.406 0.615,0.198 10 false CANL 5.208,6.625 5.667,6.823 0.458,0.198 10 false F23 5.219,6.823 6.531,7.198 1.313,0.375 10 false Power Steering ECU Assembly 5.052,5.573 5.208,5.771 0.156,0.198 10 false 7 5.063,6.104 5.219,6.302 0.156,0.198 10 false 8 5.063,1.542 5.219,1.74 0.156,0.198 10 false 3 5.063,2.073 5.219,2.271 0.156,0.198 10 false 2 3.927,0.844 4.24,1.042 0.313,0.198 10 false 17 3.969,1.198 4.125,1.396 0.156,0.198 10 false 6 3.969,1.531 4.125,1.729 0.156,0.198 10 false 5 3.948,2.063 4.26,2.26 0.313,0.198 10 false 16 3.958,5.583 4.115,5.781 0.156,0.198 10 false 3 3.969,6.094 4.292,6.354 0.323,0.26 10 false 14 2.75,6.594 3.365,6.792 0.615,0.198 10 false F115 2.74,6.76 7.021,6.958 4.281,0.198 10 false No. 4 CAN Junction Connector 0.531,6.615 1.146,6.813 0.615,0.198 10 false F150 0.531,6.792 3.896,6.99 3.365,0.198 10 false Airbag Sensor Assembly 2.708,5.583 2.865,5.781 0.156,0.198 10 false 1 2.656,6.104 2.938,6.323 0.281,0.219 10 false 12 1.813,5.583 2.125,5.781 0.313,0.198 10 false 26 1.823,6.115 2.135,6.313 0.313,0.198 10 false 27 1.344,5.594 1.958,5.792 0.615,0.198 10 false CANH 1.385,6.125 2,6.323 0.615,0.198 10 false CANL 0.698,5.938 1.469,6.135 0.771,0.198 10 false 120 Ω 0.646,4.563 1.104,4.76 0.458,0.198 10 false A84 0.656,4.74 4.177,4.938 3.521,0.198 10 false Brake Actuator Assembly 1.365,3.656 1.979,3.854 0.615,0.198 10 false CANH 1.375,4.167 1.99,4.365 0.615,0.198 10 false CANL 1.802,3.531 2.115,3.729 0.313,0.198 10 false 12 1.802,4.094 2.115,4.292 0.313,0.198 10 false 11 2.729,3.552 2.885,3.75 0.156,0.198 10 false 4 2.677,4.104 2.99,4.302 0.313,0.198 10 false 15 2.729,1.531 2.885,1.729 0.156,0.198 10 false 2 2.667,2.063 2.979,2.26 0.313,0.198 10 false 13 1.813,1.542 2.125,1.74 0.313,0.198 10 false 43 1.833,2.052 2.146,2.25 0.313,0.198 10 false 42 1.385,1.635 2,1.833 0.615,0.198 10 false CA1H 1.417,2.146 2.031,2.344 0.615,0.198 10 false CA1L 0.708,2.552 1.167,2.75 0.458,0.198 10 false A39 0.688,2.729 2.344,3.156 1.656,0.427 10 false Brake Booster with Master Cylinder Assembly 4.521,0.385 4.833,0.583 0.313,0.198 10 false A 4.844,0.385 5.156,0.583 0.313,0.198 10 false B


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)

B

5.CHECK VEHICLE TYPE
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425191C38
5.5,1 6,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 5.688,1.635 6.24,1.219 true 1.052,2.479 1.385,2.052 true 1.031,1.573 1.375,1.854 true 1.063,1.292 1.51,1.844 true 1.229,1.01 1.646,1.844 true 1.146,2.74 1.521,2.052 true 1.302,2.969 1.646,2.052 true 0.469,1.49 1.385,1.688 0.917,0.198 10 false CANH*b 0.531,2.417 1.448,2.615 0.917,0.198 10 false CANL*b 1.833,1.115 2.479,1.313 0.646,0.198 10 false F124 5.583,1.031 6.229,1.229 0.646,0.198 10 false F144 6.302,1.125 6.948,1.323 0.646,0.198 10 false CG 0.51,1.198 1.427,1.396 0.917,0.198 10 false CANH*c 0.677,0.896 1.594,1.094 0.917,0.198 10 false CANH*d 0.625,2.688 1.542,2.885 0.917,0.198 10 false CANL*c 0.76,2.906 1.677,3.104 0.917,0.198 10 false CANL*d 0.188,0.125 1.104,0.323 0.917,0.198 10 false *a 4.573,0.135 5.49,0.333 0.917,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Hybrid Vehicle Control ECU


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN junction connector
F124-12 (CANL) - F144-4 (CG)
F124-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F124-13 (CANL) - F144-4 (CG)
F124-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F124-14 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C39
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 1.177,2.281 1.51,2.052 true 6.302,1.208 5.688,1.646 true 1.177,1.552 1.521,1.854 true 0.625,1.458 1.542,1.656 0.917,0.198 10 false CANH*b 0.625,2.219 1.542,2.417 0.917,0.198 10 false CANL*b 6.354,1.094 6.802,1.375 0.448,0.281 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.833,1.115 2.5,1.385 0.667,0.271 10 false F124 0.177,0.156 1.094,0.354 0.917,0.198 10 false *a 4.531,0.177 5.448,0.375 0.917,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F124-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F124-13 (CANL) - F144-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C317371C85
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 2.083,1.896 1.635,0.188 true 1.719,1.906 1.396,0.448 true 1.344,1.906 1.146,0.781 true 1.448,3.302 1.719,2.188 true 1.115,2.99 1.333,2.188 true 1.823,3.573 2.094,2.177 true 5.708,1.646 6.417,1.167 true 2.521,1.917 3.104,0.833 true 2.531,2.188 2.667,3.083 true 2.896,2.188 2.99,2.75 true 2.906,1.917 3.354,1.083 true 0.729,2.781 0.969,2.177 true 0.51,2.427 0.604,2.167 true 0.969,1.906 0.823,1.031 true 0.677,1.917 0.625,1.313 true 1.125,0.083 2.042,0.281 0.917,0.198 10 false CANH*f 0.844,0.344 1.76,0.542 0.917,0.198 10 false CANH*e 0.594,0.677 1.51,0.875 0.917,0.198 10 false CANH*d 0.552,2.938 1.469,3.135 0.917,0.198 10 false CANL*d 0.906,3.24 1.823,3.438 0.917,0.198 10 false CANL*e 1.323,3.552 2.24,3.75 0.917,0.198 10 false CANL*f 2.156,0.938 2.615,1.135 0.458,0.198 10 false F116 5.594,0.948 6.052,1.146 0.458,0.198 10 false F144 6.469,1.063 6.979,1.26 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 3.427,1.01 4.344,1.208 0.917,0.198 10 false CANH*h 3.177,0.76 4.094,0.958 0.917,0.198 10 false CANH*g 3.063,2.677 3.979,2.875 0.917,0.198 10 false CANL*h 2.74,3 3.656,3.198 0.917,0.198 10 false CANL*g 0.281,0.927 1.198,1.125 0.917,0.198 10 false CANH*c 0.083,1.198 1,1.396 0.917,0.198 10 false CANH*b 0.083,2.479 1,2.677 0.917,0.198 10 false CANL*b 0.177,2.729 1.094,2.927 0.917,0.198 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Actuator Assembly *d to Brake Booster with Master Cylinder Assembly
*e to ECM *f to Steering Sensor
*g to Power Steering ECU Assembly *h to No. 5 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F116-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
F116-11 (CANL) - F144-4 (CG)
F116-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake actuator assembly
F116-12 (CANL) - F144-4 (CG)
F116-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
F116-13 (CANL) - F144-4 (CG)
F116-4 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F116-14 (CANL) - F144-4 (CG)
F116-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Steering sensor
F116-15 (CANL) - F144-4 (CG)
F116-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
F116-16 (CANL) - F144-4 (CG)
F116-7 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 5 CAN junction connector
F116-17 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK VEHICLE TYPE
Result:
Result Proceed to
for TMMT Made A
for TMC Made B



A

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)

B

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404459C66
1.833,0.583 2.208,0.833 0.375,0.25 5.031,0.583 5.406,0.813 0.375,0.229 0.823,0.583 1.771,1.354 true 0.833,0.917 1.438,1.354 true 0.875,1.188 1.125,1.354 true 0.844,1.708 1.115,1.563 true 0.833,2.25 1.792,1.573 true 0.865,2.01 1.448,1.573 true 2.167,1.354 3.115,0.708 true 2.823,1.344 3.104,1.115 true 2.823,1.563 3.083,1.75 true 5.115,1.281 5.708,2.125 true 2.146,1.573 3.031,2.146 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 3.688,0.083 4,0.281 0.313,0.198 10 false *1 1.865,0.635 2.479,0.833 0.615,0.198 10 false F178 5.073,0.635 5.688,0.833 0.615,0.198 10 false F144 0.25,0.49 1.167,0.688 0.917,0.198 10 false CANH*d 0.25,0.771 1.167,0.969 0.917,0.198 10 false CANH*c 0.24,1.042 1.156,1.24 0.917,0.198 10 false CANH*b 0.271,1.656 1.188,1.854 0.917,0.198 10 false CANL*b 0.281,1.948 1.198,2.146 0.917,0.198 10 false CANL*c 0.271,2.219 1.188,2.417 0.917,0.198 10 false CANL*d 3.146,0.552 4.063,0.75 0.917,0.198 10 false CANH*e 3.135,0.969 4.052,1.167 0.917,0.198 10 false CANH*f 3.156,1.719 4.073,1.917 0.917,0.198 10 false CANL*f 3.125,2.115 4.042,2.313 0.917,0.198 10 false CANL*e 5.729,2.104 6.042,2.302 0.313,0.198 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to ECM
*e to Hybrid Vehicle Control ECU *f to Brake Actuator Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F178-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN junction connector
F178-7 (CANL) - F144-4 (CG)
F178-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F178-8 (CANL) - F144-4 (CG)
F178-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F178-9 (CANL) - F144-4 (CG)
F178-4 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F178-10 (CANL) - F144-4 (CG)
F178-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake actuator assembly
F178-12 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C404459C67
1.833,0.583 2.25,0.833 0.417,0.25 5.042,0.583 5.458,0.833 0.417,0.25 1.448,1.365 0.781,0.698 true 1.469,1.563 0.802,2.063 true 5.74,2.177 5.156,1.26 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 3.854,0.135 4.167,0.333 0.313,0.198 10 false *1 5.813,2.177 6.125,2.375 0.313,0.198 10 false CG 1.875,0.615 2.49,0.813 0.615,0.198 10 false F178 5.083,0.625 5.698,0.823 0.615,0.198 10 false F144 0.208,0.542 1.125,0.74 0.917,0.198 10 false CANH*b 0.24,1.969 1.156,2.167 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F178-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F178-8 (CANL) - F144-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C40
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 2.698,2.542 1.896,2.063 true 6.375,1.24 5.677,1.635 true 2.854,2.313 2.021,2.052 true 1.052,2.813 1.521,2.042 true 0.969,2.531 1.375,2.052 true 0.938,1.417 1.375,1.875 true 1.042,1.146 1.51,1.854 true 2.844,1.49 2.021,1.854 true 2.74,1.188 1.896,1.854 true 1.177,0.906 1.635,1.844 true 1.208,3.052 1.635,2.063 true 0.635,0.802 1.552,1 0.917,0.198 10 false CANH*d 0.49,1.063 1.406,1.26 0.917,0.198 10 false CANH*c 0.396,1.333 1.313,1.531 0.917,0.198 10 false CANH*b 0.438,2.49 1.354,2.688 0.917,0.198 10 false CANL*b 0.521,2.76 1.438,2.958 0.917,0.198 10 false CANL*c 0.667,2.99 1.583,3.188 0.917,0.198 10 false CANL*d 2.781,2.49 3.698,2.688 0.917,0.198 10 false CANL*e 2.917,1.385 3.833,1.583 0.917,0.198 10 false CANH*f 6.427,1.135 6.823,1.406 0.396,0.271 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.833,1.115 2.5,1.385 0.667,0.271 10 false F115 2.917,1.063 3.833,1.26 0.917,0.198 10 false CANH*e 2.917,2.24 3.833,2.438 0.917,0.198 10 false CANL*f 0.198,0.104 0.865,0.375 0.667,0.271 10 false *a 4.688,0.146 5.354,0.417 0.667,0.271 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Booster with Master Cylinder Assembly *d to Power Steering ECU Assembly
*e to Steering Sensor *f to No. 5 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
F115-12 (CANL) - F144-4 (CG)
F115-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
F115-13 (CANL) - F144-4 (CG)
F115-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
F115-14 (CANL) - F144-4 (CG)
F115-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Steering sensor
F115-16 (CANL) - F144-4 (CG)
F115-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 5 CAN junction connector
F115-17 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425196C09
5.083,0.5 5.583,0.75 0.5,0.25 1.667,0.417 2.167,0.667 0.5,0.25 5.948,0.802 5.25,1.188 true 1.417,1.302 1.146,0.583 true 1.24,2.198 1.448,1.458 true 0.76,0.479 1.375,0.677 0.615,0.198 10 false CA2L 0.833,2.146 1.448,2.344 0.615,0.198 10 false CA2H 1.771,0.458 2.385,0.656 0.615,0.198 10 false F74 5.167,0.542 5.781,0.74 0.615,0.198 10 false F144 4.042,0.083 4.656,0.281 0.615,0.198 10 false *1 0.125,0.083 0.74,0.281 0.615,0.198 10 false *a 6,0.688 6.615,0.885 0.615,0.198 10 false CG
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-22 (CA2H) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-7 (CA2L) - F144-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C483084C02
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 1.719,1.906 1.396,0.448 true 1.344,1.906 1.146,0.781 true 1.448,3.302 1.719,2.188 true 1.115,2.99 1.333,2.188 true 5.719,1.635 6.417,1.083 true 0.729,2.781 0.969,2.177 true 0.51,2.427 0.604,2.167 true 0.969,1.906 0.823,1.031 true 0.677,1.917 0.625,1.313 true 0.844,0.344 1.76,0.542 0.917,0.198 10 false CANH*e 0.594,0.677 1.51,0.875 0.917,0.198 10 false CANH*d 0.552,2.938 1.469,3.135 0.917,0.198 10 false CANL*d 0.906,3.24 1.823,3.438 0.917,0.198 10 false CANL*e 2.146,0.948 2.604,1.146 0.458,0.198 10 false F118 5.656,0.948 6.115,1.146 0.458,0.198 10 false F144 6.49,0.979 7,1.177 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.281,0.927 1.198,1.125 0.917,0.198 10 false CANH*c 0.083,1.198 1,1.396 0.917,0.198 10 false CANH*b 0.083,2.479 1,2.677 0.917,0.198 10 false CANL*b 0.177,2.729 1.094,2.927 0.917,0.198 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to ECM
*e to Hybrid Vehicle Control ECU - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F118-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN junction connector
F118-11 (CANL) - F144-4 (CG)
F118-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F118-12 (CANL) - F144-4 (CG)
F118-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
F118-13 (CANL) - F144-4 (CG)
F118-4 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F118-14 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

D

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C317371C87
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 5.719,1.625 6.333,1.167 true 0.979,1.917 0.802,1.167 true 0.792,2.833 1.01,2.188 true 2.156,0.948 2.615,1.146 0.458,0.198 10 false F118 5.604,0.938 6.063,1.135 0.458,0.198 10 false F144 6.406,1.063 6.917,1.26 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.25,2.76 1.167,2.958 0.917,0.198 10 false CANL*b 0.24,1.083 1.156,1.281 0.917,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F118-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F118-12 (CANL) - F144-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C483093C01
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 2.698,2.542 1.896,2.063 true 6.375,1.24 5.677,1.635 true 2.854,2.313 2.021,2.052 true 1.052,2.813 1.521,2.042 true 0.969,2.531 1.375,2.052 true 0.938,1.417 1.375,1.875 true 1.042,1.146 1.51,1.854 true 2.844,1.49 2.021,1.854 true 2.74,1.188 1.896,1.854 true 1.177,0.906 1.635,1.844 true 1.208,3.052 1.635,2.063 true 1.198,0.688 1.75,1.844 true 1.292,3.25 1.75,2.063 true 0.635,0.802 1.552,1 0.917,0.198 10 false CANH*d 0.49,1.063 1.406,1.26 0.917,0.198 10 false CANH*c 0.396,1.333 1.313,1.531 0.917,0.198 10 false CANH*b 0.438,2.49 1.354,2.688 0.917,0.198 10 false CANL*b 0.521,2.76 1.438,2.958 0.917,0.198 10 false CANL*c 0.667,2.99 1.583,3.188 0.917,0.198 10 false CANL*d 2.781,2.49 3.698,2.688 0.917,0.198 10 false CANL*f 2.917,1.385 3.833,1.583 0.917,0.198 10 false CANH*g 6.427,1.135 6.823,1.406 0.396,0.271 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.833,1.115 2.5,1.385 0.667,0.271 10 false F115 2.917,1.063 3.833,1.26 0.917,0.198 10 false CANH*f 2.917,2.24 3.833,2.438 0.917,0.198 10 false CANL*g 0.198,0.104 0.865,0.375 0.667,0.271 10 false *a 4.688,0.146 5.354,0.417 0.667,0.271 10 false *1 0.719,3.219 1.635,3.417 0.917,0.198 10 false CANL*e 0.646,0.573 1.563,0.771 0.917,0.198 10 false CANH*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Booster with Master Cylinder Assembly *d to Power Steering ECU Assembly
*e to Brake Actuator Assembly *f to Steering Sensor
*g to No. 5 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
F115-12 (CANL) - F144-4 (CG)
F115-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
F115-13 (CANL) - F144-4 (CG)
F115-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
F115-14 (CANL) - F144-4 (CG)
F115-4 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake actuator assembly
F115-15 (CANL) - F144-16 (BAT)
F115-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Steering sensor
F115-16 (CANL) - F144-4 (CG)
F115-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 5 CAN junction connector
F115-17 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
13.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425196C09
5.083,0.5 5.583,0.75 0.5,0.25 1.667,0.417 2.167,0.667 0.5,0.25 5.948,0.802 5.25,1.188 true 1.417,1.302 1.146,0.583 true 1.24,2.198 1.448,1.458 true 0.76,0.479 1.375,0.677 0.615,0.198 10 false CA2L 0.833,2.146 1.448,2.344 0.615,0.198 10 false CA2H 1.771,0.458 2.385,0.656 0.615,0.198 10 false F74 5.167,0.542 5.781,0.74 0.615,0.198 10 false F144 4.042,0.083 4.656,0.281 0.615,0.198 10 false *1 0.125,0.083 0.74,0.281 0.615,0.198 10 false *a 6,0.688 6.615,0.885 0.615,0.198 10 false CG
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-22 (CA2H) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-7 (CA2L) - F144-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR